The aim of this report is to give a concise description of curtain walls, what it is and why they are used. It is also a description of six different but commonly used design technologies. By giving a detailed description of the different types and there special properties, the pros and cons will be clarified. The three most interesting alternatives were selected to be included in a test, to show the best alternative from a certain point of view.The parameters are:? Environment? Cost? Ergonomics? Isolation against noise and fire? DurabilityThese are important parameters in the planning and design phase.

Lattelement AB in Ornskoldsvik is one of the leading companies in Sweden in composite elements in walls, floors and roofs in particular. The company supplies elements to buildings located with a wide geographical variation, which means that the products are subjected to very different climate with regard to snow, wind and humidity. This places high demands and requires the elements to withstand large variable loads.The elements are made of lightweight beams with flanges of structural timber and beam webs made of OSB. These are bound together by nogging pieces with the same kind of structure. On top of the beams a nailed and glued plywood is added to absorb compressive forces and on the underside of the element a sheet of steel is added for tensile absorption.These elements are then attached to the building framework in different ways depending on the particular element height, loads and the structual supporting material of the frame work.

In this thesis a concept for floor hatches for foam pits has been developed. Since there is an existing solution that is powered by hydraulics and is expensive, the goal was to develop a cheaper solution, as simple as possible.A number of different concepts were developed and evaluated. A concept with five sections that are pulled to the side and stacked on each other was chosen as it was thought to have the lowest risk of crush injuries and to be easiest to manage and control. In the opening behind the foam mattress a lifting table is placed to regulate the height of the stacked sections.To be allowed to be installed in the floor of sports halls the sections must be dimensioned according to the construction standards for these types of buildings. Different dimensions of beams in steel and wood materials were evaluated and of those, who lived up to the requirements of the standard, a concept was chosen.

The purpose of this bachelor degree thesis is to analyze technical issues associated with an implementation of a low sloping trash rack with narrow spacing. A hydropower plant in Umea?lven was used as a case study. The basis for the study was a model where trash racks were dimensioned for inclinations between 25 and 45 degrees. Corresponding head loss, durability and water speed through the rack were then determined for each inclination.

Granskande av ritningar, tidsplaner och kalkyler för referensprojektet Hus N i Växjö har hjälpt oss kartlägga skalväggars för- och nackdelar. Från intervjuer har vi sedan kunnat se liknelser och skillnader om vad olika yrkesfolk i samma bransch tycker, sedan därifrån dragit slutsatser. Det är inte alltid enkelt att avgöra vilken byggnadsmetod som är att föredra för att projektet ska vara kostnadseffektivt, prefabricerat eller platsbyggd. Faktorer som byggnadens konstruktion, årstid, arbetsmiljö, resurser, tid och kostnad ska ta hänsyns till.Genom att planera bättre, öka förtillverkningen, skapa en bättre samverkan mellan byggherrar, konsulter, entreprenörer, underentreprenörer och materialleverantörer, så anser man allmänt att man kan öka industrialiseringen av byggandet. Då man kan få kortare byggtider och lägre totalkostnader. .

HAFA Bathroom Group has given us the assignment to develop a standardized back panel for their bathroom cabinets. This cabinet is going to be applied to most of their current and future cabinet solutions. To this point, they have constructed unique suspensions-and back panels for most of their cabinet models. They have also been forced to pull wiring and assemble the cabinets differently because of factors like; position of the wall sockets, dimensions of the cabinets and their shapes.The company wants to distance themselves from their current solution, firstly because the cost of having manpower to design each individual suspension solution, secondly because they will save a lot of money when the manufacturing process requires a minimum of components to be constructed. As a result of this, the company can use their resources better to develop future products.The main idea is that the consumer isn?t required to change the suspension or back panel when they decide to buy a new cabinet.

Hudiksvall Municipality will build a new preschool. The goal is that the pre-school should reflect the municipality's environmental goals and meet building regulations. The wall structures that are compared in the report is an insulated wooden frame and a frame of lightweight concrete blocks from H + HWall structures are compared within the areas of U-values, air tightness, thermal storage capacity, fire ratings, moisture, durability, emissions and environment. In these categories the two wall structures will be rated in a scale from 1 to 5 and then the categories are weighted against each other. The weighting is based on Hudiksvall Municipality's assessment of the categories importanse for their final selection.The results of the comparison show that the concrete structure is recommended for the construction of pre-school with 27.55 points against the wooden structures 23.70 points.

Glulam is a product that was engineered to make use of timber in a more efficient way. Bychoosing timber of similar quality and discarding natural defects during production, thedevelopment of a stronger cross-section is achieved.Carbon fiber is a relatively new material with a high tension capacity. This feature is used toexamine how the bending capacity of the beams improve by adhering carbon fiber laminateson the lower edge of the beamsThe strength of the material is tested with three experiments: carbon fiber on the bottom of thebeam (a), carbon fiber attached to the lower sides of the beam (b) and carbon fiber in thebeam, covered with a layer of wood (c)The results show that the first case, where the carbon fiber is attached to the bottom of thebeam, gave the best result with an increase in capacity of 59 % compared to the nonreinforcedcontrol. The other two cases also show an improvement in capacity, beam-type 3had a capacity increase of 47% and beam-type 4 increased with 25 %Tests were also made with glulam beams reinforced with fiberglass, but these tests were notanalyzed in depth because the purpose was to compare the capacity to carbon fiber. Thisbeam improved its capacity by 40.3%.The tests show that carbon fiber as a reinforcement material for glulam is a good choice whenthere is a requirement for stronger cross-sections in both new production and renovation ofold buildings.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

This is a booklet with information and inspiration about precast retaining walls. The three chapters contain information about concrete as a material, how the surface of the wall can be altered, and a chapter with ideas for a new precast wall. I have obtained information through books, interviews, lectures and fairs. The retaining walls on the market do not correspond to the requirements of the Landscape Architects I have interviewed. I have therefore considered their opinions in the chapter containing my new ideas for new retaining walls.

In this thesis tests has been performed on the pull strength of screws glued into glulam beams.The experiment is based on the already approved method whereby the diameter of the drilled holes is the same as the screw outer diameter of 1 mm or bigger. The screws strength class shall not be less than 4.6 (EN ISO 898-1:1999, 1999).The difference in the experiments that were performed where that the drilled diameter were 1 mm smaller than the outer diameter of the screw so that the screw thread was worked into the wood.In the tests the gluing where made on M8 glulam beams. The screws where drilled at and angel of 90°tangental to the fiber direction with a diameter of 7 mm. The gluing of the screws where made in three different depths and where later exposed to pulling forces. The results showed both pulling breaks and screw breaks when they reached their maximum capacity.

This report compares two different types of insulation with regards to fire and moisture. The materials were tested for the company Fiskarhedenvillan AB, for a wall and a roof construction that the company currently uses in the establishment of Sweden's first certified passive house for international standards.Their current material, Rockwool, is compared to a relatively new material on the Swedish market called SEALECTION Agribalance sold by the company ISO Green AB. The material is a type of polyurethane insulation. This insulation material would result in a more efficient execution of the construction as it provides waterproofing and is applied more easily than Rockwool. From a fire standpoint, literature studies and discussions with fire experts led to results.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

To save energy it?s popular to build houses with low energy loss. In these houses the walls are keeping a lower temperature in the external side which leads to a higher relative humidity. In addition more material, such as wood studs, are used which means that there is more moisture to dry. More moisture in combination with higher relative humidity may pose a higher risk of microbial growth.

The landscape with its associated historical tracks and remains are an important part of our cultural heritage that we consider important to conserve. The stone walls are an example of historical remains that helps to build up this cultural heritage. It is a landscape element that today usually is being associated with the old cultivated landscape, where they mainly functioned as boundary markings and fences. Today, the stone wall is a valuable element in the landscape with ecological, culture-historical and aesthetic values. Since the stone walls arose as elements in the landscape a lot has been changed within the agriculture.