The aim of this thesis is to make a comparison between solitary graves and graves in grave fields from the Roman Iron Age on Gotland, Sweden. Differences in burial customs, morphology, dating, gender, age, grave-goods and social status are compared between 19 solitary graves and graves in three different grave fields in different parts of Gotland. An attempt is made to explain these differences and to discuss which functions the solitary graves had. Discussions about whether it is possible to distinguish social status and gender with the help of grave-goods are also made in connection to the determination of status and sex..

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This is qualitative study of, four teacher´s views on the use of iPad in teaching and learning. In addition, I will examine the disadvantages and advantages of iPad use as a teaching tool in preschools.My questions are:What is the practical use of tablets in preschools today?Are preschool teachers using the tablet as a teaching tool? If so, how?Is the use of tablets in preschools contributing to children´s social interaction, as well as between children and teachers` social interaction?The purpose of this study was to find out how the four teachers uses the iPad as a teaching tool in the interaction between children in preschool. I have chosen to use Vygotsky?s and John Dewey´s theories.

Real-time systems are required to answer to external stimuli within a specified time-period. For this to be possible, the systems behaviour must be predictable. The use of active databases in real-time systems introduces unpredictability in the system, e.g. due to their use of active rules. The behaviour in active databases is usually specified in ECA-rules.

The aim of this study is to find out if the former students think that they have made use of the courses they have taken at the Natural Resource Use Programme specialised in Animal Husbandry at Lillerudsgymnasiet or if the courses should be exchanged. In the study it is assumed that a course can be useful professionally, for further studies and in private life.The main questions are: Have the former students made use of the courses they took at the Natural Resource Use Programme specialised in Animal Husbandry at Lillerudsgymnasiet? Was it the right decision to replace the course Horses?I have sent a questionnaire to all the students who graduated between 2003 and 2007. Out of 107 questionnaires I received 66 replies (62 %). All students have studied the same mandatory courses but different eligible courses.

The project was carried out together with OC Off Course who manufactureand distribute mainly electric bikes.In today?s society, alternative sources of transportation becomes more andmore present and several bicycle sharing programs arises in major citiesacross the world every year.Something that doesn?t exist too much as of yet is bike sharing programsthat uses electric bikes. An electric bike is a convenient way oftransportation as well as a good way of avoiding traffic. With an electricbike you avoid having to sweat when biking over hills or when you need totravel over longer distances.The goal of this project is to develop a bike sharing station according tothe functions need to be met.This thesis Is based on Fredy Olsson´s methods principkonstruktion aswell as a couple of concept generating methods from Kenneth Österlin.From this, a number of sketches were made that later was evaluated inseveral steps in conjunction to a set of specifications. A 3D model of theselected concept was later made in CatiaV5 for a complete product..

I detta examensarbete utvecklas ett solcellsstativ i trämaterial. Ett idékoncept fanns somgrund för hur stativet skulle kunna utformas. Detta har vidareutvecklats, till färdigt systemanpassat för tillverkning.Resultatet blev ett fackverksstativ i trä bestående av vinklade halva oktaeder i rad.Trädetaljerna binds samman med knutpunkter i formsprutad plast, som med klämkraft hållerfast trädetaljerna. Knutpunkterna är konstruerade för att minimera åverkan på träet samtmotverka röta.Systemet är verifierat både genom beräkning, simulering och jämförelse med liknandekonstruktioner. Materilavalet är gjort med systematik enligt Ashby, Material Selection inMechanical Design.

Weland AB är ett familjeföretag som startade 1947 med sitt huvudkontor i Smålandsstenar. Här finns ungefär 250 anställda som jobbar på ca 60 000 kvadratmeter. Ryggraden i Welands verksamhet är tillverkning av pressvetsad gallerdurk som går att se i konstruktioner som trappor, både spiral och raka.Projektet grundar sig i att ljudnivån vid en maskin för kapning av gallerdurk är hög och därför har personalomsättningen också varit hög. Syftet med projektet är att konstruera komplement till en kapmaskin för att göra den helautomatisk. Det skulle göra att en operatör inte behöver vara närvarande mer än för att förse maskinen med material, programmera maskinen och bortföra pallar med färdigt gods.

Our report procedure identification of instability and disturbance in an automatic manufacturing line of processing and assembling of chair sliding rails at Sapas manufacturing department in Vetlanda.To obtain a stabile ground we have mapped the material flow to receive a comprehensive view and to visualise connections.We have examined cycle times at different stations in purpose to identificate bottlenecks. The result of our examination showed that the bottleneck of the line was the brush station. This leads to that the expected bottlenecks identificated by Sapa gets a delay time and by that a longer cycle time.Interruptions has a clear negative influence at the line performance so we have also assemble data through the operators report list and compiled these in order to find out the interruptions effect on the line. The outcome during our assembled period was that the reported interruptions corresponded about 30 percent of the total available production time. This has a clear negative effect on the line productivity and efficiency as we have calculated in order to get the present status..

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

The use of energy is an important question in today´s society, and a substantial part of the energy that is used today is used in our homes. To lower this usage is vital, and there are regulations in place both on the national and the local level, that say that new apartment blocks must be built to consume less energy, which in the end will lower the impact on the climate.One way to make the housing sector more environmentally sustainable, is to produce energy issions that are bad for the environment, for example to build wind turbines close to or even on the buildings, so called urban wind power. The scope for this report is to see if urban wind power could be a sustainable alternative for the residential area that Svenska Bostäder plans to build in Albano in Stockholm.There are extensive scientific theories regarding wind and wind power, and a literature study is made to investigate past knowledge in the area. Efforts have been made to find earlier trials with urban wind power and, both scientific research and trials where urban wind power actually has been installed. The theory chapter deals both with the wind itself and how electricity can be generated from wind.

In the centre of Bromma, east of Brommaplan is the part of Bromma named Riksby. Riksby was built in the early 1940:s as a part of the westward expansion of Stockholm. Other places that were built at the same time was for ex. Stora Mossen and Abrahamsberg. This work is about the outdoor environment of the housing co-operative of Brickbandet.

In this project an iPhone application for storing food and drink experiences was developed with focus on an easy interaction design. The already existing market of similar applications were studied and evaluated to extract their positive and negative features. Interviews with experts within the food and drink business where made in the pre study to get a good perception of how to divide and categorize the sections in the application. To optimize the usability, workshops with potential users with different technical experiences where continuously held during the development of the design.During the development two variants of development environments where evaluated. The final result of the application was developed in the environment that made the best impression and seemed to be the best alternative.The resulting product has a thought out design meant to be easy to understand, even for the first time users.