Induction motors, often referred to as the workhorse of the industry, play an important role in production today. Therefore, it's important to diagnose any faulty induction motor prior to failure to avoid costly and time consuming production stops.This thesis compares methods for diagnosing induction motors in operation, MCSA, Park's vector approach and the standard method used by Swedish industries today. By simulating broken rotor bars and short-circuit in one of the windings, each method is tested and the results are compared using matlab.The results need further verification due to uncertainties of the condition of the test motor, even though the experiment gives a hint of the different advantages of each method. A combination of the methods should be able to tell if the motor needs further examination..

This is the final documentation of the basis that can be the foundation of how to solve theproblem with leaking hydraulic oil in a shoe press at the company Albany InternationalAB in Halmstad, Sweden.The project has been performed at Halmstad University as a degree project commissionedby Albany International AB. The purpose of the degree project was to find a way ofdetecting the hydraulic leak of a shoe press. The reason is that the shoe press runsunattended during nights and weekends, this can cause an extensive decontaminationwork and production stop if leak. The hydraulic oil could be leaking in large amounts orslowly as a fine mist. The development of a working system that can detect a hydraulicoil leak and stop the machine before a large amount of hydraulic oil leaks out wouldconsiderably reduce the cost of the decontamination work.

In each classroom there is a teacher with good intentions wanting what´s best for their pupils. But grades and tests in mathematics from 2009 in Sweden shows there is a crack between the subject being taught and the learning child. The purpose with this research is to find an understanding from a teaching and learning perspective of which teaching method is more suitable for teaching and learning mathematics by doing a comparison between two methods. The main question is:What are the advantages and disadvantages of the traditional and the laboratory method of teaching, supported by the two keywords teaching method and learning?This C-paper is based on a qualitative research aiming to gather an in-depth understanding of human behavior.

In this master thesis work, a new method called MultiScat, is compared with the conventional method with alfa-correction, for computing concentrations from intensities in X-ray spectrometric analysis. The conventional model is a linear model, which only takes the photoelectric effect into consideration. It doesn't consider Rayleigh and Compton scattering even though it has a great impact on the measured intensities. Here MultiScat differs a lot. MultiScat is based on a solution of the Boltzmann transport equation.

The purpose of this thesis is to investigate the possibility to make small, cheap and ultra low power sensor platforms, connected in wireless networks for monitoring of home and industrial environments. The concept is based on ideas from our supervisor, Jerry Lindblom. The developed system consists of a generic platform for different sensors, a receiver and software. A GPRS module from RO Rollytech AB and a database from Gema Industri AB have been modified and used to demonstrate an example of a complete system. To the platform, it is possible to connect any resistive sensor and any sensor that can act as a switch.

This study investigates whether the site index curve method (SICM) and the growth intercept method (GIM) can be used for site index predictions in younger Norway spruce (Picea abies (L.) Karst.) stands than recommended by current guidelines. For SICM it was thus investigated whether the method could be used for stands younger than ten years, and for GIM it was tested whether a starting point for the intercept measurements could be used below the recommended 2.5 meter. This was tested based on measurements taken from experimental stands in Tönnersjöheden Research Forest. For GIM it was found that the method can only be used when the TH-trees of a stand have five complete intercepts above 2.5 meters. For the method to be applicable beyond this, it will be necessary to adapt the underlying equations, perhaps following the Canadian example where a 1.3 meter intercept start is used. In conclusion it is not currently possible to apply the approach beyond the current recommendations. For SICM, SI predictions are accurate for the study area already form year three.

Executive SummaryThis final thesis has examined the effects of an increased centralization and better coord­in­ation of the distribution logistics at ABB in Västerås. The company is today strongly decent­ralized and there is a minimum of collaboration between the 20 business units. This is why the questions were raised; how could the business units coordinate outbound logistic activities and what effects would that provide. The obj­ect­ive of this final thesis is to provide basic data for a future decision-making which desc­r­ibe these effects.The report has mapped out the factors that are important to ABB in an evaluation of their logistic activities and how the outbound logistics work today. The four factors are cost efficiency, delivery service, environmental impact and logistics capability.

The global Positioning System (GPS) provides location and time information as long as there are unobstructed lines of sight to four or more GPS satellites. However, when this is not the case the signal may be inaccurate or sometimes even completely blocked. In these situations the Inertial Navigation System (INS) is an appropriate choice for positioning.  An INS has already been proposed in a previous thesis by Erik Andersson and the objective of this thesis is to fuse the GPS with the INS in a proper way. A part of this project is to decide the reliability of the GPS.Three methods for GPS reliability detection have been proposed. One method based on the statistical properties of each of the separate systems, and two methods based on the statistical properties of the residuals between the GPS and INS.

There have been, in some rare cases, difficulties with clamping of inserts with U-holesin their tool holder. According to the complaints, the inserts could not be properlyclamped or could fracture when clamped. A study has shown that variations inclamping behaviour are mainly depending by the position of the screw hole in the toolholder and the centering of the screw hole in the insert.The focus of this project has been the centering of screw hole in insert. It has beenshown that the screw holes are not always enough centered in the insert. Theproblem may occur after a certain step in the production, i.e.

In order for a judgement to be enforceable in another Member State, there is a certain requirement for an "intermediate? court procedure, a so-called exequatur procedure. An exequatur procedure is both expensive and time-consuming. The average cost of the procedure within the EU is 2 200 euro in a case without particular difficulties. In more complex cases, the cost of the procedure can be validated up to 12 700 euro.

The waste of material is a big expense for manufacture companies caused by lack of quality. The cost by lack of quality often totaled to a big percentage share of the turnover when all cost related to lack of quality is included. New manufacturing systems like Lean production or Just In Time demands better internal quality for the manufacturer. To make those manufacturing system with small and none buffer stock successful the quality improvement continuously have to be developed.Measuring of waste of material in Bubs Candy?s factory where not simple due to the products does not have a permanent weight during the manufacturing process.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

The Swedish potential of electricity production from roof mounted solar panels has been determined in three steps: accessing the existing roof top areas, simulating the amount of electricity solar panels can produce on these areas and finally analyzing how large the necessary economical change is to make the solar cells profitable.The total existing amount of roof top areas are 319 square kilometers and the area distribution follows the distribution of people. This leads to an installed power of 47,9 GW which are expected to produce 49,0 TWh electricity per year. If the quality of the electricity is prioritized the highest the power is reduced to 3,7 GW, generating 3,8 TWh yearly, but if the hosting capacity is calculated from Sweden?s total electricity need, the capacity is 42 TWh per year.Today, solar panels are not profitable in Sweden for houses, even though there is a subsidy of 35 % of the investment costs, discounted in 25 years. The profitability is calculated with a cost of capital of 5 %, a price on electricity of 1 SEK/kWh and an investment cost of 20 SEK/Wp.

A clean and affordable energy source for cooking is deficient in developing countries. People rely on fuels that contribute to environmental, social and health problems.Biogas is an alternative energy source and an increased investment in small-scale biogas production can in several developing countries be found. Several projects have started to use the technology in developing countries because of the benefits with biogas. Some cases in the establishment of biogas plants have succeeded and some have not. The study is a literature review supplemented by two field studies.