Public concern and the need of responsible way of doing business have brought forward the issue of sustainability at the forefront of discussion in the last decade. Even though, food retailers are playing an important role in the economy, they are exposed for criticism by media and consumers for any socially and environmentally irresponsible business practices because, the potential environmental and social impacts from their operations are significant. These impacts need to be recognized and properly addressed. The main objective of this study was to assess the sustainable business management of a cooperative food retail business in Sweden, known as Konsum Värmland (KV). The necessary data and information on history and status of KV, and its practical activities concerning the implementation of sustainable development programs as well as the motivation and challenges encountered by KV during the implementation were gathered via reviewing different documents, research papers and press releases; interviewing decision makers and other personnel in KV and other researchers from Swedish University of Agricultural University who have investigated KV.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

Abstract:Theoretical framework:  The Theory of Suffering by Katie Eriksson was used.Aim: The aim was to illuminate factors that influence women?s choice to seek care for urinary incontinence.Method: This literature review was based on a sample of nine qualitative and quantitative studies. Modified templates were used to assess the quality of the studies. Analysis of the results was done withmanifest content analysis.Findings: Findings made clear that the experience of shame is a central factor for women not to seek treatment for their urinary incontinence UI. Women had to have severe loss of quality of life in order to seek help for their UI, and the loss of quality of life had to be subjectively larger than the feeling of shame.

Companies constantly strive for the perfect order which enables them to satisfy and retain their customers. This is a difficult process that can be facilitated by using different picking technologies. In this study, a research of the picking technologies Pick-to-Light and Pick-to-Voice have been made to investigate when each technology is suited.In order to collect relevant information and data to be able to answer the question formulation, a qualitative study with interviews have been made. The purpose of this essay was to investigate Pick-to-Light and Pick-to-Voice to see when each technology is best suited and to see what the differences between the technologies are. With our essay we wanted to help manufacturing companies to make the right decisions when implementing a picking technology.The results showed that those picking technologies give companies a higher picking quality and an increased work efficiency since the order picking is faster to perform, and that picking errors are reduced.

In order to measure the quality of the logs, one can with help of Fast Fourier Transform technique get the signals resonance peaks. With help of these peaks you can see whether the quality of a tree is good or bad. This report contains the work of a where a program has been developed to be able to process a vibration created by an automatic hammer hitting on a log of wood. From the processed signal the program should be able to show both the raw wavesignal and the processed measured data from the resonance peaks. Beyond the raw wavesignal and resonance peaks the program should also be able to control the automatic hammer.

In order to measure the quality of the logs, one can with help of Fast Fourier Transform technique get the signals resonance peaks. With help of these peaks you can see whether the quality of a tree is good or bad. This report contains the work of a where a program has been developed to be able to process a vibration created by an automatic hammer hitting on a log of wood. From the processed signal the program should be able to show both the raw wavesignal and the processed measured data from the resonance peaks. Beyond the raw wavesignal and resonance peaks the program should also be able to control the automatic hammer.

In order to measure the quality of the logs, one can with help of Fast Fourier Transform technique get the signals resonance peaks. With help of these peaks you can see whether the quality of a tree is good or bad. This report contains the work of a where a program has been developed to be able to process a vibration created by an automatic hammer hitting on a log of wood. From the processed signal the program should be able to show both the raw wavesignal and the processed measured data from the resonance peaks. Beyond the raw wavesignal and resonance peaks the program should also be able to control the automatic hammer.

In order to measure the quality of the logs, one can with help of Fast Fourier Transform technique get the signals resonance peaks. With help of these peaks you can see whether the quality of a tree is good or bad. This report contains the work of a where a program has been developed to be able to process a vibration created by an automatic hammer hitting on a log of wood. From the processed signal the program should be able to show both the raw wavesignal and the processed measured data from the resonance peaks. Beyond the raw wavesignal and resonance peaks the program should also be able to control the automatic hammer.

Prescribed burning was commonly used for site preparation in Sweden to establish new forests until the 1960?s, when mechanical scarification was introduced. During recent decades the interest in prescribed burnings has increased again, mainly due to certifications of forestry stating that 5% of the regeneration areas should be burned on dry and mesic soils. The objective of the study was to evaluate actual influence of prescribed burning compared to other site preparation on stand stem density, growth parameters and tree damages for Scots pine (Pinus sylvestris L.) after direct seeding and planting. The study also attempts to simulate growth until first thinning.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.