Membrane bioreactors (MBR) combined with biological phosphorous treatment (Bio-P) has been investigated if that could be an alternative to the future expansion with conventional active sludge treatment at Lundåkra wastewater treatment plant (WWTP) in the proximity of Landskrona, Sweden.The results showed that the surface demand in the biological treatment will be reduced with 67% with the MBR-alternative compared to a conventional activated sludge process. The nutrient removal in the MBR-solution was decreased or unchanged for nitrogen-, phosphorous- and organic parameters. However, the energy demand will increase with an estimated cost of approximately 1 million SEK annually. Moreover, the extra chemical consumption is estimated to cost 370 000 SEK annually.The disturbances caused by filamentous bacteria such as sludge dispersal could be resolved with MBR-technology because the membranes are not affected by these organisms. The Bio-P process combined with MBR-technology works if the wastewater recirculates from the membranes to an aerobic zone.In the proposal, there will be a new pre-treatment step, for instance hole screens.

Aitik-gruvan utanför Gällivare är en av Europas största koppargruvor. Malm bryts i dagbrott och släntdesignen bygger till stor del på undersökningar och karteringsarbeten från 1970- och 1980-talet. Idag når dagbrottet betydligt djupare nivåer jämfört med då dessa studier utfördes. Det var därför aktuellt med en ny undersökning för att avgöra om det råder liknande eller förändrade förhållanden beträffande spricksituationen i dagbrottet. I detta examensarbete utfördes sprickkartering med hjälp av digital stereofotogrammetri, i syfte att kartera nya blottade delar i dagbrottet.

Various Fusarium species causes some of the most common cereal diseases worldwide. Besides the yield losses that can be a result of these diseases, strains from several Fusarium species can produce mycotoxins, some very toxic. The aim of this study was to investigate which Fusarium species and how many that occurred in winter wheat grains from Mälardalen and Kalmar län, if there was any difference in the distribution of Fusarium fungi between the regions and the potential within species to produce mycotoxins belonging to the group trichothecenes. Winter wheat grains collected in 2009 from ten fields (unsprayed plots) in the two regions were analysed for Fusarium species. PCR was used to amplify the TEF region where after the samples were sequenced.

Logistics planning for a construction site is usually limited by traffic flow to and from the workplace. The geographical location of the construction site is determined by roads around the workplace and opportunities for well-functioning logistics. Inventory of material is often impossible because of the frequently small workspaces. As a result, a concern relating material handling remains . Even before the establishment of a construction site, it is required in the construction industry to eliminate errors that might arise in the planning stage.

Uppsatsen handlar om det arbete vi utfört åt Prevas AB i Karlstad. Uppdraget gick ut på att synkronisera tre olika systems kalenderfunktioner så att det som skrivs i en kalender syns i alla. För att klara det behövde vi först undersöka hur de tre systemen fungerade vilket delade upp arbetet i en utredningsfas och en konstruktionsfas. Utredningsfasen ledde till att vi begränsade arbetet till att endast omfatta en envägskommunikation mellan två av systemen i konstruktionsfasen. Detta arbete beskrivs i detalj i uppsatsen..

During the transportation of logging residues (LR) the material´s low density is a problem that results in low use of pay-load capacity. Comminution or compression of LR are possible methods to increase pay-loads. In the present thesis studied a bundling machine which was mounted on a truck chassis, and the subsequent transport and crushing. The truck bundler created bundles that were larger and longer than other bundling equipment on the market. The objectives were to determine the total time consumption and its allocation over work element and machinery, to measure dry matter (DM) content of green and brown LR-bundles.

AbstractBuilding Information Model/Modeling/Management (BIM) is a tool that allows for efficient working methods. BIM saves time and money while providing the potential for visualization. This method of working is based on a 3D-model, and then a fourth and fifth dimension are connected. 5D modeling means that a spreadsheet creates cost estimates based on the 3D model. This provides opportunities to carry out calculations in the early stages of the projects. Calculations are currently performed manually and do not contribute to the development that the construction industry requires.

Quality can be defined as the ability of a business to satisfy their customers? needs and expectations. Total Quality Management is defined as the way to prevent, appraise and improve the entire organization to increase the product quality. In order to systematically increase quality in an organization, there are different quality systems in use. One example is process management, which is to divide the activities of processes.

As a company it is required to work with strategies to minimize costs such as packaging and logistic costs. The increased market of industrial produced wooden buildings results that the time and the cost which the packaging of prefabricated building elements consume, is experienced to be in greater need of development than before and demands a better solution. The aim with this dissertation was to discover how the development of the handling of the packaging can improve the packaging process. The goal was to present improvement proposals for a simplified and thereby a more efficient production in time and cost perspective.The packaging process which includes packaging, handling, storage and transport were studied. Interviews were made with participants from the market for manufacturers of wooden houses and a case study was made at the company A-hus.

The thesis aims to compare differentpiping materials in heating systems interms of cost as well as to illustratethe impact of energy characteristics ofdifferent materials over its servicelife. The methods used for costcalculations regarding piping are alsoto be examined to highlight thedifferences between template basedcalculations and more carefully executedones. The work is delimited to discusspipes of steel, copper, plastics andcomposites. The aim is that the resultcan be compiled to illustrate the prosand cons of various materials whenevaluating investments.The main object of the survey is part ofa heating system in the office-block KVSommaren located in southern Stockholm.The configured piping system is designedwith the mentioned piping materials andis used to make up the data for flow andcost calculations. The differentmaterials are calculated in both aconventional manner with a supplementarycost for additional fittings and with amore accurate quantification of thecomponents.

This report examines some common or otherwise interestingnon-cryptographic hash functions with respect to the number of collisions when used in hash tables for different types of hashkeys. The report answers which of the examined hash functions can be seen as the best performing for the chosen hashkeys. To compare the different hash functions, an experiment which studies avalanche effect behaviour is carried out. The experiments also calculate the fraction of colliding hashkeys, and the distribution of hashkeys in hash tables is studied using Karl Pearson?schi-squared test.

A manufacturing machine at the engineering company Sandvik Coromant has a positioning table which task is to move an item linearly. The positioning table has a linear motor capable of high velocity and acceleration. This makes it possible to achieve short cycle times and a more profitable production.The purpose of this thesis is to bring forward a new concept which is more adapted to the requirements of the positioning table. The reason is that the current positioning table provides an unnecessarily positioning accuracy of 0.01 mm, while the requirement for the positioning accuracy is just 0.1 mm. The goal is to reduce manufacturing and component costs.To develop a suitable solution an approach for the concept development process has been performed.

Det här examensarbetet bygger vidare på vårt tidigare projektarbete. I det tidigare projektarbetet etablerade vi oss som produktionsgruppen ?3Kproject?, där vår största ambition var att nå ut med egenproducerad musik till allmänheten främst via DJ:s och Internet. Nu har vi valt att bygga vidare på det arbetet och gå ett steg längre, en ny inriktning med en ny frågeställning. Frågeställningen lyder: * Hur ser utvecklingsprocessen för en fanbase ut? Via momenten produktion, promotion, marknadsföring och distribution tänker vi oss söka svar på den frågan.

There is an uncertainty in the market for grain forcing the meat/milk producers to review alternative feeds to a larger extent, in order to get control over the feed costs. This has led to that the meat/milk producers need to have a good knowledge regarding how the different feeds influences the animals and which technical equipment to use for handling. For those that produce their own feedmix, there is a need to put interest in new crops and their characteristics to be able to get the knowledge of what is required for their own production. It is beneficial to keep an open dialogue with advisors to be updated in new crops and new technology for feeding. When mixing feed at farm level, the legislation is not very clear since it the target group is large scale mixing plants. We have brought up the most important rules and regulations from the EU parliament Council as well as the ones from the Swedish Board of Agriculture (SJV), regarding feed mixing on farm and factory level. We have studied beans and pea at two different moisture levels, in order to evaluate how the moisture level affects the distribution of particles when milling with a plaitmill and a hammermill.

Background: The construction industry is Sweden?s single most important industry branch with a significant influence on Sweden?s wealth. The political restrictions that once controlled the industry are today almost gone. This combined with an unbalanced supply and demand situation on the Swedish constructions market, caused by urbanisation, has led to increased pressure on the Swedish construction companies who now are forced to find new methods in their struggle to contain or increase their competitive advantage. Purpose: The purpose of this thesis is to survey: which strategic variables are of great importance in today?s Swedish construction industry with focus on the four main actors, JM, NCC, PEAB and Skanska.