The economic prerequisite to many farmers in Sweden after the EU membership and the new agriculture policy has generated large demands on the farm management. Until year 2004 you got a grant based on what you had produced and not on consumer demand. In 2005 a new economic aid (Mid Term Revue) was introduced and the conditions has changed again. Due to this I have chosen to do a cost-benefit analysis on a case, to investigate if the present production is sustainable in the future. My conclusion is that the profitability is acceptable even if the farm has a high debt. But to make the production more profitable the products produced should be refined as much as possible at the farm, to get maximum economic return.

A clean and affordable energy source for cooking is deficient in developing countries. People rely on fuels that contribute to environmental, social and health problems.Biogas is an alternative energy source and an increased investment in small-scale biogas production can in several developing countries be found. Several projects have started to use the technology in developing countries because of the benefits with biogas. Some cases in the establishment of biogas plants have succeeded and some have not. The study is a literature review supplemented by two field studies.

This thesis shows the result from investigations of methods that use distance vectors when matching pictures. The distance vectors are available in a distance map made by the Euclidean Distance Transform. The investigated methods use the two characteristic features of the distance vector when matching pictures, length and direction. The length of the vector is used to calculate a value of how good a match is and the direction of the vector is used to predict a transformation to get a better match. The results shows that the number of calculation steps that are used during a search can be reduced compared to matching methods that only uses the distance during the matching..

To increase the quality in their products ABB is working towards a cleared order concept. That means that all customer specified options are to be known before they start with order calculations and construction. As it is today they use paper checklists to achieve this. One order may have several reactors, and for a reactor there can be several different alternatives. For each alternative a new checklist must be filled out.As of today all reading of the customer specification and checklist fill in with is done by hand by different persons, and sometimes the same data is read more than one time.

Denna rapport är en litteraturstudie i geometri, topologi och fysik, skri- ven med avsikten att förbereda för studier i allmän relativitetsteori. Den har karaktären av en lärobok och dess målgrupp är personer med kunskaper likvärdiga med en kandidatexamen i teknisk fysik, teknisk matematik eller liknande. Rapportens fokus ligger på matematiska metoder för allmän relativitetsteori och förkunskaper nödvändiga för att förstå detta. Texten avslutas med några inledande exempel på allmän relativitet som demonstrerar några av begreppen som avhandlas i rapporten. Rapporten behandlar sitt ämne på en inledande nivå och dess främsta syfte är att ge en överblick och en motivation för fortsatta studier..

At the beginning of 2011, Sweden started using the European rules for structural design, the Eurocodes, instead of the previous national rules. In both the previous rules and the Eurocodes, it is possible to dimension concrete columns using tabled values. However, the required cross section measurements have increased considerably. Moreover, it is possible to dimension concrete columns using calculations, however, this is unusual.The development of a fire in a fire cell can be divided into the growth stage, the fully developed fire and the cooling phase. The duration of each phase, as well as the temperature, is dependent on a number of factors, e.g.

AbstractToday, too many construction projects are delayed and deviates from the budget. Agood project management is the basis for successful construction project. The mostcommon planning methods in the construction industry is currently Gantt chart andCPM. The problem with these is that focus is only at the time of the project anddoesn?t handle the budget.

Executive SummaryThis final thesis has examined the effects of an increased centralization and better coord­in­ation of the distribution logistics at ABB in Västerås. The company is today strongly decent­ralized and there is a minimum of collaboration between the 20 business units. This is why the questions were raised; how could the business units coordinate outbound logistic activities and what effects would that provide. The obj­ect­ive of this final thesis is to provide basic data for a future decision-making which desc­r­ibe these effects.The report has mapped out the factors that are important to ABB in an evaluation of their logistic activities and how the outbound logistics work today. The four factors are cost efficiency, delivery service, environmental impact and logistics capability.

Approximately 60 million cubic meters of round wood are transported every year with trucks in Sweden and stand for 15 % of all truck transportation in the country. The big amount that is transported results in many haulage companies works in different parts of the country with different conditions to get a good flow on their transports. Today the transport pricing is very general and the payment consists of the unit round wood they are transporting and the distance of the transport. The purpose of this study were, from the freighter and the haulage company?s perspective, try to find ways to change the today applied transport pricing to more differentiated and compare them to historic payment of transportation.

In order for a judgement to be enforceable in another Member State, there is a certain requirement for an "intermediate? court procedure, a so-called exequatur procedure. An exequatur procedure is both expensive and time-consuming. The average cost of the procedure within the EU is 2 200 euro in a case without particular difficulties. In more complex cases, the cost of the procedure can be validated up to 12 700 euro.

The waste of material is a big expense for manufacture companies caused by lack of quality. The cost by lack of quality often totaled to a big percentage share of the turnover when all cost related to lack of quality is included. New manufacturing systems like Lean production or Just In Time demands better internal quality for the manufacturer. To make those manufacturing system with small and none buffer stock successful the quality improvement continuously have to be developed.Measuring of waste of material in Bubs Candy?s factory where not simple due to the products does not have a permanent weight during the manufacturing process.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

The Swedish potential of electricity production from roof mounted solar panels has been determined in three steps: accessing the existing roof top areas, simulating the amount of electricity solar panels can produce on these areas and finally analyzing how large the necessary economical change is to make the solar cells profitable.The total existing amount of roof top areas are 319 square kilometers and the area distribution follows the distribution of people. This leads to an installed power of 47,9 GW which are expected to produce 49,0 TWh electricity per year. If the quality of the electricity is prioritized the highest the power is reduced to 3,7 GW, generating 3,8 TWh yearly, but if the hosting capacity is calculated from Sweden?s total electricity need, the capacity is 42 TWh per year.Today, solar panels are not profitable in Sweden for houses, even though there is a subsidy of 35 % of the investment costs, discounted in 25 years. The profitability is calculated with a cost of capital of 5 %, a price on electricity of 1 SEK/kWh and an investment cost of 20 SEK/Wp.

A clean and affordable energy source for cooking is deficient in developing countries. People rely on fuels that contribute to environmental, social and health problems.Biogas is an alternative energy source and an increased investment in small-scale biogas production can in several developing countries be found. Several projects have started to use the technology in developing countries because of the benefits with biogas. Some cases in the establishment of biogas plants have succeeded and some have not. The study is a literature review supplemented by two field studies.