Background:Life-cycle costing (LCC) is an investment calculation that takes intoaccount operating costs throughout the investee lifecycle. LCC calculations are mainly usedto evaluate investments that have no revenue side. Attempts to apply the LCC calculations forbuilding-related investments have occurred since the 1980s. Despite the advantages ofusing LCC calculations, use has not passed through in full. The main obstacles have beenidentified as a lack of relevant input data, and insufficient experience of workingwith LCC calculations.

The study took place at a food corporation in Växjö, Sweden. It describes a building that contains four tanks in which glucose syrup is stored. The purpose of the study was to calculate the amount of heat that leaves the building and the amount of heat that is supplied by the installed heating equipment. Before the calculations could be implemented, all the systems that supply the building with heat had to be examined. With a small amount of information from earlier studies, the work to gather all the data necessary for the calculations began.

Calculations are an important part of planning around a construction project. From concept to completion of the project calculation is a tool to try to predict the actual cost. During the production stage in particular, deviations occur which makes the actual cost different from the calculations.This thesis is done in collaboration with JM Residential Stockholm. The study includes a cost follow-up in which a comparison was made between the calculated production cost and actual cost for the five projects. The aim of the study was to observe the most common reasons that a project deviates from the calculated production cost and then summing these causes in a number of categories.

This essay includes the planning and designing of a house as well as writing a rapport about howto increase fire safety in small buildings.More than 6000 homes burn in Sweden every year (Brandskyddsföreningen, 2012c). Thedevastation and the costs are usually very high. This report examines possible measures to reduceboth personal injuries and economic losses resulting from house fires in small buildings.Swedishbuilding regulationsplay a major role when it comes to constructional fire safety. However therequirements inSwedish building regulations are very low for small buildings and this is anargument for raising the requirements.The report shows and describes possible methods to build safer with regards to fire in terms ofmaterials and different building structures. Major focus has been on fire cells but other solutionsare also examined and described.

Tången 2 is a building situated in Stockholm, Sweden. It´s built in the 1930s and contains both residences and businesses. The property owner, Diligentia AB, wants to lower the energy use in Tången 2. This report consists of an energy audit which clarifies the specific circumstances linked to Tången 2. Collected knowledge is then used, together with the results from the literature study, to decide energy measures to proceed with.

The aim with this study was to collect fundamental information, and to plan, a windpower farm in Juddhult , Småland in southern Sweden. The goal is to collect the bestavailable projecting planning support. The pieces of this projecting planning supportthat will be presented is; Environmental Consequence Description (MKB), productioncalculations, comparisons between different plant types, economic calculations, evaluatethe economy and give some farm design suggestions. The imagined wind farm will belocated in forest environment and which may cause a number of new problems. Specialinterest that will be affected, where special consideration because of the forestenvironmental is requested is, hunting, wetlands, ancient monuments and windturbulence.

AbstractAbetong in Falkenberg manufactures, among other things, small prefabricated concrete buildings for housing various installations, such as electric transformers.The aim of this dissertation is to reduce the time needed to design such buildings, by way of finding a number of standardized buildings. Standardized in such a manner as to incorporate both the needs of the manufacturer (Abetong) and its customers.To analyze the needs of the parties the work has included a market survey and calculations on the strength of these buildings.One survey was a letter questionnaire to all of Abetong?s customers who have, in the past, ordered these types of building. The aim of the questionnaire was to establish how the customers want these buildings designed.Another survey conducted was an inventory of all of Abetong?s previous projects where these types of building were manufactured.

This examination paper is an energy-inventory of Soldathemmet at the regement in Halmstad, in colaboration with Fortifikationsverket in Halmstad. The building is first an foremost for the soldiers, where they can go for a cup of coffee or watch TV. There is also a museum and a drivers school in the building. Calculations have been done with two computerprograms; VIP+ and ISOVER Energy. The results were well matched with the statistics that were provided by Fortifikationsverket.

This study is one of five that has been done based on Lunds Energi?s planned investment in bioenergy. The plan is to build two large burners, at Örtofta, that?s going to be supplied with biofuels. In this study I take a closer look on the profitability when you choose to sell your cereal as bioenergy. I?ve been calculating with selling the straw from the grain crops and winter rape, selling the rye weat as whole crop and fertilize the hemp with sewage sludge.

Chunks and Tasks is a programming model based on the C ++ programming language. This programming model is used for electronic structure calculations, among other things.The purpose of this project is to improve the CHT-MPI software library for Chunks and tasks, so that calculations of matrix-matrix multiplications are performed more efficiently than they do with the existing software library. The software library is based on the work stealing method, which is a method the software library for Chunks and Tasks uses for the distribution of the calculation work. The considered way to improve the software library is by modifying the work stealing method in a way that makes the distribution of calculation work happen in a more efficient way , which will lead to calculations performed faster than before.Two different modifications of the work stealing method were tested and it led to two new methods, Method 1 and Method 2, which distributed the calculation work differently. Method 1 did not give results that were compatible with the theory, since the calculation time with this method was much longer than the previous method.

In Sweden there are currently two separate guidelines you may use whenperforming calculations on frameworks, BKR and the Eurocodes. Although at theend of 2010 you are not allowed to use BKR any longer and only the Eurocodeswill be viable. The aim of this thesis is to explain how the Eurocodes and EKS work and alsohow they compare to the current guideline BKR. Similarities and differencesbetween these guidelines are also discussed so that the reader will get a betterunderstanding of how the Eurocodes are applied. The areas discussed are asfollows:Principles and adviceSafety ClassesSymbols and IndexesLifespanLoads and partial coefficientThe thesis also deals with the impact that this transition into a new guideline willhave on corporations, guideline costs, education and computer software. As anexample a rough estimate on what costs this transition will create on a companywith 20 employees is also included. Calculations have been performed in order to investigate how the design valuesdiffer between the two guidelines, the Eurocodes and BKR.

At a manufacturing company, due to the competition the price is reducedtowards the manufacturing cost. Therefore it is important to maintain control ofones costs and keep calculations up-to-date.This thesis deals with cost accounting at a aluminium-processing company. The report focuses on calculating machine cost per hour since the manufacturing costs are the major part of the total product cost.Managers on the company believe that the costs they use in calculations todayneither is up-to-date nor advantageous in a market aspect and due to that their calculations need to be revised. The machines cost per hour is a major part in the manufacturing calculation. The company wants to provide a competitive price that also covers their costs.

ABB is one of the world?s leading engineering companies in power and automation technologiesand their solutions improve performance while lowering environmental impacts for energycompanies and industries. ABB FACTS designs equipment and plants for series and phasecompensation.This thesis has been performed at ABB FACTS on the Mechanical Design (DM) department inVästerås, Sweden. The purpose of the thesis was to develop and design calculations andsimulation tools for ABB FACTS?s standard series capacitor platforms.

Rapid population growth and the fact that phosphorous is a limited resource implies that the question regarding an efficient use of phosphorus is of great importance, and consequently,that the phosphorous use efficiency should be as high as possible. The view on phosphorous use efficiency, and how this is calculated, has varied over time. This has had great implications on what type of research that has been conducted, which have resulted in an inconsistency between the academic?s view on the subject and recommendations received by farmers. The purpose of this paper is to calculate the phosphorus use efficiency in the Swedish long term fertility experiments.

Our education at Halmstad University was completed with a degree project. Our task was to improve an already existing pneumatic damper to Nederman in Helsingborg. Overall we have made necessary calculations to make the design of the existing damper smaller. When these calculations were done, we moved on with an analysis of the existing damper in order to figure out what improvements could be made on each part of the damper. The result of this project is a smaller and a more supple design of a pneumatic damper. To this we have also created complete drawings, calculated material expenses; we have also created an assembly of a pneumatic damper in Catia v5..