Bravida is one of Scandinavia's leading suppliers of technical installations and services. According to Bravida an installer loses around 35 per cent of their daily work. It?s the time aspect that?s going to be examined in this thesis. The purpose of this thesis is that the student in question is to investigate the activities of the installers that works with this project, identifying where and how time losses occur and come up with suggestions for improvement.Methods used in this work is literature studies, observational studies and interviews.

The graduation essay has been carried out in co-operation with Kalmar Industries in Lidhult, Sweden. The purpose of our essay was to develop a complete construction solution on a hoist that could lift a laying wheel, lift it up and then turn it 90 degrees. After that the wheel shall be placed in a special holder.The background of the essay is a record of reports of damage wheels when they been incorrect lifted with a forklift. The hoist shall be used together with the same forklifts that manage the wheels today. Together with our instructor at Kalmar Industries we developed a requirement specification and from that we got free hands.However this was not the main task from the beginning, then a simular hoist should be develop but used directly in the assembly workshop without using a forklift.We started to find principle solutions that later was evaluated against the requirement specification.

The findings in this case study are mainly based on material collected during a field trip with a fellow student to Laos in February-March 2005, which was sponsored by Sida through a Minor Field Study scholarship. The original interest was to study a political aid project (Governance and Administrative Reform Project Luang Prabang, GPAR LP) in a country like Laos with very complex preconditions such as one-party polity. In Laos my interest in evaluation of political aid grew mainly because I found out that the two donors in the project, Sida and the UNDP, had reached different conclusions in their respective evaluations of the project.The main interest in this thesis has been to study how donors have evaluated a political aid project. The study shows that Sida and UNDP used, what in the literature usually is referred to as, Conventional evaluation as methodology when they conducted their evaluations of GPAR LP. The study also shows that the main reason for the different points of view that are expressed in the evaluations depend on a lack of dialogue and consensus, regarding for the project crucial concepts, rather than choice of evaluation methodology.

This project was conducted during the spring semester 2013 at mechanical engineering program at University Halmstad. The project was conducted in collaboration with MPQ Consulting in Halmstad. MPQ Consulting is a newly established company looking to take step into the product development world. The company has already had ideas and existing products. One of the ideas is to construct and design a form of beach games whose rules are based on the volleyball rules.

This thesis has been done in collaboration with Peab Stockholm Building 3, which is a region within the Peab Sverige AB. The report is based on a survey and studies of Peab business management systems and production literature. For general information gathering has literature from well-known sources collected in libraries and through the Internet. It shows through the work that Peab has routines for experience feedback in the construction process, but that these procedures work in a small scale and the practical work experience feedback does not work at all. This is also something the construction industry in general also perceived as problematic. The questions in the report are of a wide scale and concerns construction errors cost, how the employees perceive that the company takes advantage of the skills and the mental stress in production line. The goal is to find how Peab Stockholm Building 3 will work on the experience feedback to allow for better productivity. In conclusion, the report author tries to demonstrate what can lead to increased productivity and improved work experience..

External Thoughts is a studio based project with its purpose to throughworkshops establish contacts and create a dialouge about the content of contemporarygraphic design. The project also aims to apply a design curaticalmethod where the designer is both client and contractor, client and designer.We also wanted to investigate the design content as open-source and examinethe school versus the Internet?s future role in the design and for thedesigner. The project is a collaboration with Rasmus Östgård Ohlson fromBeckmans..

An increased number of participants in the construction industry is asking for accompanying terrain models to the project in order to get a better understanding of the field. When the desire to create buildings that fit together nicely with the surrounding area is increasing, it becomes more and more important to have a broad base of knowledge about the ground on which the building is to be erected. Terrain models are also very useful in the planning of logistics, documentation for landscape architecture projects, and billings for mass calculations.Surveys for creating terrain models can be performed with laser scanning. The advantage of laser scanning is the time-effective surveying, the detailed information as well as the ability of application in complex environments resulting in a cost-efficient project. With this in mind our thesis was defined in collaboration with the company Bjerking AB in Uppsala in order to investigate if there were any softwares suitable for terrain modeling.

Bachelor thesis, Trolley Innovation Project, has been unique in the sense that it has been carried out over the borders of Sweden. Iacobucci S.p.A, located outside of Rome in Italy is one of the largest manufacturers of interior equipment for aircraft in the world. With approximately 30% of the market Iacobucci S.p.A is one of the world's largest manufacturers of catering trolleys.The aim has been to produce a new competitive catering trolley for the airline industry. With customers and users in focus, the project team found that weight, ease of use, ergonomics and design were important aspects. Having a low weight of all the interior is particularly important when there is lots of money for the airlines to save in reduced fuel costs.

In this essay the renewal of the modern sacred art has been examined through the creation of three works of art from the art project ?Kyrkorummet?. The aim has been to show that renewal of the modern sacred art is best accomplished by the combination of the artist history and Bible knowledge and the open mindness of the beholder towards the new and creative, in order to communicate the gospel in modern time.The large extend of the art project demanded a selection of the art works. Therefore, three were chosen and they show the last supper and the baptism in a renewal way including both symbolism and creativity. To complete and facilitate the analyses, a theme, light and water, have been used as well as relevant theories in art history with Kandinsky as main art critic.Through the art project and it?s teaching, history in combination with present time through visits in different and modern churches, thoughts have been stimulated and the result has been new works of art that speaks of our time.

Thesis completed by Johan Arvidsson, Alex Rasooli and Pontus Winroth, students at master program Product development and Design at the School of Engineering in Jönköping Sweden. The project comprises 30 ECTS credits and was carried out during the semester in the autumn of 2007.It was carried out in cooperation with Eksjöverken AB, subcontractor within the truck industry with special knowledge within the area of complicated machinery construction work. Job initiators at Eksjöverken were Mats Svanberg and Kjell Nygard. Dag Holmgren was acting as a tutor from the university. The task was to develop tools for trucks, primary toolboxes but in case of time also under run protection.

BackgroundToday a common approach to solve a complicated problem is to assemble a temporary workforce in order to solve the problem by working together within a project. One of the difficulties with working in projects is to maintain the planned budget. Working hours and costs are often exceeded. Many companies presume that any certain project will succeed, a presumption that leads companies not to anticipate risks involved in a project. In companies today there is seldom time for evaluation or moderation of a project, in order to have time for evaluation there is a great need for an adequate planning of the project.IntentThe intention with this study is to create a model for planning, budgeting and evaluation of projects within consultancy companies.MethodWith the help of interviews and discussions within the group Hamnar och Byggkonstruktioner at Sweco has evidence to present a proposal on planning, budgeting and monitoring been developed.ResultsA model has been developed to ease for consultancy companies to plan, budget, monitor and evaluate projects.

Partnering is a collaboration method where the contractor and the client work together, based on a mutual trust towards each other and with a common goal for the project. The method originates from the United States where it was early adapted by the U.S. Army Corps of Engineers. It later spread internationally where the United Kingdom and Denmark were early in Europe to see the potential with partnering, to help aid with the issues they were having where construction projects kept running late, going over budget and lacked in quality. By using partnering you can achieve a shorter building time, improved work relationships and enhanced efficiency and cost effectiveness.

Japan is the first industrialized country that is experiencing the threat of a rapidly declining and aging population. This has shifted the focus and the limelight is now on the matter that for a long time has been ignored. That is, the Japanese women?s situation in the society. This thesis seeks to point out the relevance of gender in the construction of leadership in order to get a deeper understanding of the Japanese women?s situation today.

The main goal of this project was to develop some sort of a diverter for pipestransporting waste in a vacuum system. This unit was supposed to be both cheap andeasy to serve/exchange worn out parts. With a limited space to install the pipeexchanger, the challenge was to keep it as compact as possible without constructingbends with to small radius or to sharp angles as this would wear out the system a lotfaster than planned. The system was also supposed to be able to handle clothes andscrubs from hospitals. Having too much sharp edges or angles would tear the clothesapart.

This project is the result of a cooperation between HalmstadUniversity and EABAB. The aim of the project was to create a macro that would help EABAB automate the process of designing steel trusses. When run in Microsoft Excel, the macro imports and processes coordinates from a calculator program. The data is then imported into the Building Information Modelling software Tekla Structures, which creates a 3D structural model of the steel truss.The macro saves much time in the project planning process and also helps minimize the risk of design flaws caused by human error. .