Degree project in Logistics, 30 credits, The Business Administration and Economics Programme, Linnaeus University, 4FE05E, Spring 2013Authors: Ida Nilsson & Malin Skacke Tutor: Peter Berling Examiner: Helena ForslundTitle: Increased profit potential by controlling customers? ordering patterns -­? A case study at OatlyBackground:Oatly manufactures and sells oat-­?based products and deliveries are today carried out through an external distributor. The company is going through a re-­?organisation and will in the future be managing stock keeping and planning of deliveries with their own resources. The customers? present ordering frequency and volume differ substantially, leading to unnecessary costs.

In Sweden, the demand for bio energy has increased in recent years due to the current energy and climate debate. In 2008, the energy supply of Sweden was 612 TWh, biofuels accounted for 123 TWh of these. Stumps have been highlighted as a potential fuel in recent years and the Swedish Forest Agency expects a technically and biologically feasible potential of 20.7 TWh annually between 2010 and 2019. The idea of utilize stumps is not new. During the 19th century stumps were used for tar production and during the 70?s and 80?s attempts were made to use stumps in the pulp industry.

Modern sawmills are using the raw-material and the production-capacity more efficiently today, due to rising raw-material prices and higher production costs. Log sweepness has a negative effect on the sawn yield, for sawmills with straight-sawing. It is desirable that these logs could be sorted based on more criteria, if it increases value-yield and consequently the utilization of raw-material. Bow-heights over 1 cm have a negative effect on sawn yield, since the surface of the mantle cuts down in the sawn pattern. Some of these small bow-heights reduce the logs yield of value which affects the production planning negatively. Nearly half of all the Swedish logs have a bow-height over 1 cm.

The annual demands for forest fuels increases in Sweden. At present, large unutilized biomass resources is found in young, dense forests from which about five million oven-dry tonnes (ODt) (23 TWh) could annually be extracted as forest fuel. But harvesting small trees give high logging costs and new cost-efficient harvesting techniques are therefore required. The aim was to study the productivity of Vimek 608 BioCombi in forest fuel thinning of Lodgepole pine and to calculate the economy of the harvesting and estimate the thinning quality. The time study was performed in Åmarken in the county of Västerbotten.

One of the most important components of a harvester is the crane. Most harvester cranes are only possible to pivot (or horizontally rotate) at the crane pillar. Cranab in Vindeln, Sweden, has developed a new type of harvester crane which has an extra pivot point on the outer boom. This makes it possible to reach around residual trees, easing thinning work in dense stands. The aim of the study was to analyze if the use of a pivoting outer boom (POB) crane gave an increase in thinning production and if there were any differences in time consumption between the work elements for the POB crane and a conventional crane. A Valmet 911.3 equipped with a POB crane was used in the study.

Vår studie bygger på artiklarna ?Fads, Martingales and Market efficiency? och ?Volume and Autocovariances in Short-Horizon Individual Security Returns? och är ett replikat av dessa.Studiens syfte är att undersöka förhållandet mellan förändringar i aktieomsättningen och veckoavkastningar för enskilda aktier på Stockholmsbörsen..

The efficiency of the harvesters work is more often reviewed, than the work of the forwarders. In a local Stora Enso office the differences between the harvesters reported volume of timber, and the actual volume delivered to the industry had been noticed. Therefore, the decision was made to do a review on the forwarders work. The review was conducted together with a worker from Vmf Qbera, who is working daily with wood measurement, in order to get a valid evaluation of the logs. Eight sites were included in the survey, and on each site 50 logs were marked. Approximately one third of the marked logs were pulpwood, and the remaining logs marked were timber.

In order to facilitate testing of anesthesia machines a patient simulator has been required by Maquet Critical Care AB. A patient simulator has been developed to reduce expensive and time consuming animal experiments and temporary lab arrangements. The patient simulator has been developed and designed to simulate human lungs with regards to anesthetic uptake, production of carbon dioxide and heating and moisturizing exhaled air.The system comprises a container and a test lung to simulate the volume and the dynamic of the human lung. The simulation of uptake of anesthetics has been implemented by pumping a fraction of the gas from the container through a bypass circuit with an active charcoal filter that adsorbs volatile anesthetics. The flow through the bypass circuit is generated by a pump and is controlled by a linear valve.The resulting performance of the patient simulator has fulfilled the requirements.

The system tungsten-oxygen has potential of being suitable for decorative coatings since ceramic coatings are often hard and wear resistant, and since modulations in oxygen content or incorporation of small ions could give bright colours. The aim of this report was to investigate the relationship between process parameters and  the properties of the films, with the wear resistance being of special interest.Samples with tungsten to oxygen ratios in the range of 100:0 to 25:75 at% were made using reactive sputter deposition, either with constant gas flow, or gas flow controlled by optical emission of the plasma. The hysteresis of the system, which means that a certain gas flow will cause different pressure and/or target voltage depending on in what way the flow is reached, makes it interesting to control the process where the system makes the steep change from metallic tungsten to ceramic tungsten oxide. This is difficult and thus requires precise control equipment.The samples were analysed using X-ray diffraction, X-ray photoelectron spectroscopy and an empirical wear test suitable for small components like cell phone cover for example, in order to characterize the structure, composition and wear resistance of the coatings. The results could be divided into three groups: (I) tungsten-like, with very low oxygen content; (II) mixed phase and (III) tungsten oxide like, with oxygen content close to 75 at%.

Today green tree retention, together with leaving dead wood, is a common practice with the aim to reduce negative impacts on biodiversity and environment due to clear-felling. To better understand whether this conservation practice also makes a long-term difference, it is important to know what happens to these trees after harvest. Few studies have made an assessment of what happens to retention trees over a longer time period. In this study I inventoried retention trees that were left at clear-cuts six, twelve and eighteen years ago. I carried out a re-inventory of 57 retention patches (divided into free-standing tree groups, small swamp forests and edge zones) and free standing dead trees, spread over 25 previous clear-cuts in central Sweden.

Information technology and globalization has led to an increasing competition and service production has been more and more independent of locations. This has made a market of outsourced telephone costumer service possible. Due to high establishment the market has been saturated and with that price has sunk. Customer companies have the last few years got more negative to outsourcing of their telephone customer service as they through operating the customer service internally want to get closer to their customers.In the empirical study the writers try to figure out which companies the callcenters should try to aim towards to get long and profitable cooperation. This will be done through deducing guiding principles from theories about how different factors around companies costumer service should look like.

Prosthetic leg can give a negative psychological effect to the user, which ends up in decreased self-esteem and that the user hides his handicap. xCover gives a more natural volume and a cool look. xCover changes the look of the prosthetic leg C-leg. The product is constructed by us, Patrik Svensson and Magnus Zetterqvist, for Christoffer Lindhe at Lindhextend AB. Christoffer has hired Martin Bergman at Smedjan 17 to make the design.

This report provides a comparison between the products cellular concrete, foam concrete and LECA concrete. The questions to be answered during the work is how the cellular concrete stands up in cost terms to the existing competitors on the market, how the concrete products differ in design work, and in which situations the concrete varieties are preferred to use.Cellular concrete is a variant of ordinary concrete, with the difference that the ballast is exchanged from stone materials to expanded polystyrene beads (EPS). This substitution gives a product with higher insulation values but lower weight than ordinary concrete.The work was carried out by designing a survey which was sent to two hundred randomly chosen companies across Sweden, to see the building industry?s opinion of the product cellular concrete. The survey showed that cellular concrete was equals its competitors in terms of price, while the product was said to be more flexible, quicker and easier to cast.Then some of the companies, who participated in the survey, were interviewed to see more carefully, how the price, the workmanship and the time for casting and dehydration differed between the products.

Light has always fascinated humans but ever since the invention of the first light bulb, the use of artificial lighting has accelerated dramatically. Darkness has never been as rare as today and the overuse of lighting has created a new phenomenon called light pollution. Most living beings are biologically dependent on the recurrent twenty-four-hour rhythm of light and darkness, called the circadian cycle. Human beings are evolutionary developed after this circadian rhythm and the effects of constant artificial light is yet unknown. Scientists fear the consequences of constant lighting and what it means physically, mentally and philosophically for the human species.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.