In Uppsala, Sweden, Vattenfall has a combined heat and power plant. On the premises there is an engineering workshop with old fluorescent and mercury lamps that need to be replaced. This provides a great opportunity to save energy and money by installing more efficient lighting. The main purpose of this study was to present two functional and energy efficient lighting systems including control system. The lighting systems were designed by investigating the working environment, measuring illuminance and by simulations in the software DIALux.

In a sustainable society the use of renewable energy and recycling of materials is of high importance. Wastewater treatment plants use large amounts of energy in the processing of wastewater. This study seeks to evaluate wastewater as an energy resource and to examine treatment plants potential to become sustainable energy producers. The study is based upon the internal processes of Himmerfja?rdsverket.

Problems with the current energy system, which partially relies on non-renewable fuels, are increasingly recognized. Emissions of greenhouse gases from fossil fuels may speed up global warming, which in turn leads to a number of negative consequences. Nuclear energy is risky and relies on consumption of a scarce resource. This leads to a demand of renewable energy that is also economically feasible. One possible renewable source of energy is solar energy.

Industries with energy costs as a large proportion of their total costs are greatly affected by the instruments deployed to cope with the Swedish climate and energy policy goals. With energy costs representing more than 30 % of the total costs, tomato cultivators are one of the affected industries. In order to remain competitive with other countries, a more resource- and cost-efficient cultivation of tomatoes in greenhouses is desirable in Sweden. Based on the concept of industrial symbiosis, this study investigates the prerequisites for a resource-efficient production of locally grown tomatoes in Sweden through the utilization of low grade industrial waste heat. The study is based on the foundry industry as the supplier of waste heat.To investigate the environmental, technical and economic potential of the exchange of waste heat, a comparative life cycle assessment, an inventory of the supply of industrial waste heat in Sweden, a compilation of potential technologies for the recovery of low grade industrial waste heat for heating greenhouses and a comparative life-cycle cost calculation were carried out.

In the spring of 2006 a pilot project was initiated by The Rural Economy and Agricultural Societies of Sweden together with The Swedish Ornithological Society in order to increase collaboration between bird watchers and farmers. The project as a whole comprised 11 farms in South-Central Sweden. The aim was to benefit the decreasing populations of bird species related to the agricultural landscape. The purpose of this master thesis was to study how similarities and differences between bird watchers and farmers regarding opinions about nature, landscape, agriculture, birds and nature conservation have influenced the collaboration. Four of the farmers and five of the bird watchers that participated in the project were included in this study.

With increased deployment ofintermittent renewable energy, such aswind and solar power, energy storagebecomes necessary to help reduceproduction peaks. Thermoelectric EnergyStorage is a method still in researchphase, which stores electricity in hotwater at a temperature of 120 ° C. Thisthesis aims to examine whether theThermoelectric Energy Storage would bepossible to integrate into existingpower generation such as a combined heatand power plant, and how the technologypotentially could function in theelectricity market. ThermoelectricEnergy Storage consists of a chargingprocess and a discharging process, bothoperating by the working fluid CO2. Toincrease the efficiency of theThermoelectric Energy Storage, wasteheat from the district heating networkis integrated.A model of the Thermoelectric EnergyStorage has been developed and it wascalculated by thermodynamic propertiesof the working fluid, CO2, in thevarious process steps.

Aeroseum is an aviation museum located in an old military underground hangar. The ventilation system in the hangar is designed for the military purpose of the hangar. This design includes a solution with air flowing through the space between the construction of the hangar and the rock surface. The solution is intended to avoid a buildup of inflammable gases. This design leads too high humidity levels in the hangar.

This thesis work has been carried out at the consultant company Pöyry Sweden AB in Norrköping, whom performs the task for E.ON heating Sweden AB, Händelöverket in Norrköping. The report shows methods to manufacture slurry consisting of fly ash and water. The slurry shall be pumped into several former oil storage rock shelters that E.ON has put into operation for the specific purpose. The ash mixture also develops hydrogen gas in contact with water.The work has aimed to produce different suggestions of methods and equipment that can be used for the objective. Mixing method and security issues were in centre while working with the suggestions.

The company Sol & Energiteknik wanted to examine the possibility to make a standardhouse totally energy independent. Based upon this I have, during the spring of 2007,examined the possibilities available at the market today through litterature studies, contactwith several companies and reading reports at the internet.The first thing to examine has been to determine the energy consumption for a standardhouse, and find out if there are better technologies to be used for energy conservation.My conclusion in this matter is that there are possibilities today for building a house moreenergy efficient.When I had reached the point at which my design for the house was decided, I also hadto choose the different products to use to produce energy as well as to store that energy.To produce heat and electricity to the house I decided to use a wind turbine and a solarwater heater.The most difficult part of designing a house that is energy independent is that theproduced energy must be stored somehow. Storing the heat is relatively easy beacuse theheat can be stored in a large water tank. The electricity is a bigger problem beacuse itmust be stored in batteries, which today are too expensive to be used in a standard house.In the future producing and storing hydrogen might be used to produce electricity, buttoday that technology is both expensive and not tested enough.My final conclusion is that a standard house can not be built to be totally energyindependent today, unless it is very expensive to connect the house to the electricitynetwork. As an alternative solution I came up with a proposal for a house which isconnected to the electricity network and have some amount of own produced energy.This house prooved to be a good investment if you choose to build it today, and it couldbe a very good investment in the long run beacuse energy prices increase every year..

The purpose of this master?s thesis is to contribute to the development of business relationships between a supplier and its customers. The research area and research problem was further developed into three research questions. The research questions concerns the following subjects: the substance of business relationships and dimensions within relationships management that can be used in order to contribute to the development of a company?s business relationships.

This thesis is intended to review and create a greater understanding for the history and originsof printed scraps from late eighteenth century to the beginning of the twentieth century.A questionnaire survey was sent out to several Swedish museums, containing questionsconcerning their collections, possible exhibits, special difficulties and types of damagesconcerning scraps and their current storage. A visit to the Gothenburg city museum storagewas made to take a closer look at their scrap collection and how they were stored. Thisresearch resulted in an understanding regarding the current situation of printed scraps, whichunfortunately appears to be quite poor and inattentive. These results are presented in the firstchapter.The second chapter describes the history of printed scraps, followed by a chapter presentingrelevant printing techniques and technology. This is followed by various chapters dealing withhow the printed scrap has been used through the ages, history and development of motifs andthe album's significance.

Traditionally, rolling mills use emulsions based on a mixture of oil and water for lubrication. Since two years ago SAPA has been using (instead of oil) a synthetic lubricant so called conditional emulsion for hot-rolling of aluminum. This lubricant is water based and homogenous at ambient temperature, but switches to a two-phase system at heating above the cloud point.This project aims to validate and if necessary modify an existing HPLC method for quantifying two out of three key components (A, B and C) in the conditional emulsion. Attempts to develop a method to quantify the pH adjusting components, X and Y were also made. These two methods are required to optimize the lubricant.Due to the complexity of the components, it has been difficult to present a method for quantification, and HPLC with ELS detection was chosen after a long series of trials.

That animals should be able to express their natural behaviours, even in captivity, has become a more important issue lately. Nowadays Zoos work much more with educating people and helping conservation projects for endangered species. This is two important reasons for making the environment as natural as possible for zoo animals. Both in captivity and in the wild capuchin monkeys have been seen to use tools such as stones and sticks to get food and are therefore seen as a natural and important behaviour for them. This study was carried out to evaluate a specific sort of environmental enrichment where a group of three capuchins had to use sticks to get different kinds of food out of bottles.

Med ett energikombinat vid Lillesjöverket vill Uddevalla Energi energieffektivisera samt sänka temperatur på återkommande fjärrvärmevatten, för att kunna utnyttja rökgaskondensorn effektivare. Uppdraget var att utreda mängden tillgänglig energi under sommarhalvåret och utföra en matematisk kalkyl som ska ligga till grund för val av tork. Valet stod mellan två alternativ av tork där storlek på värmeväxlararea och investeringskostnad skilde dem åt. Sedan följde dimensionering av fjärrvärmeledning samt cirkulationspump från fjärrvärmenätet till tork. Syftet var att ge Uddevalla Energi ett tekniskt beslutsunderlag för val av storlek på tork samt dimensionering av energiöverföring till densamma.

This report describes the construction of a climate-cabinet for testing of HV-cards (High Voltage) produced at VG Scienta. The main part of the report describes all the different components of the cabinet. The most important parts are a PID regulator from Eurotherm model 2408, a solid state contactor (SSC), a thermocouple, a finned resistor from DBK and different fans. The report even includes the connection between components by cable wiring, isolation, grounding, fuses and shaping of metal goods.As the cabinet also communicates with a computer, the report includes the solution of the data communication using the software iTools from Eurotherm. The communication part includes information about a converter that converts EIA422 to USB.The cabinet was produced at a company, called VG Scienta, in Uppsala during the spring 2010.