Abstract 1.The purpose of this study was to investigate the effects whole body vibrations on maximal strength, power output and neuromuscular activity in m. pectoralis major during bench press.Participants consisted of 35 male and 9 female military high school students (m=23, 1 years). On the basis of initial maximal performances in bench press the participants was divided into two experiments groups and one control group. Intervention groups performed a specifically designed push up program on a vibrating plate respectively a step board during 12 weeks Initial load at 60 % of 1 RM showed an average of 46, 5 kg. All groups showed an average increase of 13 kg for each person after 12 weeks.

Abstract The core is the center of gravity in our body. Injuries and overload in the joints, is the most common reason for not be able to work in Sweden today. A god strength capacity in the core is important for secure and effective movements, as well for active athletes, as for non athletes. The increased number of employees, who report in sick today, has been correlated with psychological bad health. New methods to deal with mental and physical health problems among people can indicate to the fact that Yoga in the western world has increased its members, due its spiritual and physical recognition in favor of well being.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

Background: Practical blood flow restriction (pBFR) combined with resistance training has been proven to facilitate muscle strength despite training at low intensity. However, research investigating the effects of long-term pBFR-training and its periodization with strength training (ST) at a higher intensity is lacking, as well as the effects of occlusion training on blood lactate levels (BLL) over time.Purpose: To compare the effects of 2 weeks of pBFR training followed by 2 weeks of ST (BFR-ST) with 2 weeks of ST followed by 2 weeks of pBFR training (ST-BFR) on anaerobic performace and BLL.Method: 5 adults (age 23 ± 2 years) with a minimum of 1 year of ST experience were recruited and randomized into BFR-ST (n=2) or ST-BFR (n=3). Anaerobic performance was measured using a 30-s Wingate-test and BLL samples were collected <1 and 5 minutes post-Wingate. Data and samples were collected before the intervention and after the 2 protocols.Results: No differences were seen between groups in anaerobic output or BLL after 4 weeks of training (p>0,1 for all values). A decrease in time to peak power (tPP) were seen in both groups with an advantage for BFR-ST (-37 ± 8 %) over ST-BFR (-27 ± 22 %).

Thesis purpose The study aims to examine the effects vertical and horizontal line extensions might have on the total parent brand equity in terms of strength and its baseline product regarding of market share, loyalty and penetration under an elapsed period of time. The study aims to investigate a number of actual conducted line extensions effect on the above mentioned aspects of Kellers (1993) definition of brand strength as a part of the total brand equity. Methodology The effect of a number of line extensions of the parent brands and the baseline products is being examined in terms of market share, loyalty rate, cannibalization and market penetration. The thesis is focused on the correlations between these different parameters during a certain elapsed time ratio in order to test our theoretically routed hypothesizes in a deductive manner. Occasional correlations are derived from an indexation of data collected from the Gfk database. Theoretical perspective The study is derived from Kapferers (2004) definition of brand equity, where he is dividing the concept into three parts. This study is focused on Brand strength in particular, which is one of the parameters in the above-mentioned theory.

In this thesis tests has been performed on the pull strength of screws glued into glulam beams.The experiment is based on the already approved method whereby the diameter of the drilled holes is the same as the screw outer diameter of 1 mm or bigger. The screws strength class shall not be less than 4.6 (EN ISO 898-1:1999, 1999).The difference in the experiments that were performed where that the drilled diameter were 1 mm smaller than the outer diameter of the screw so that the screw thread was worked into the wood.In the tests the gluing where made on M8 glulam beams. The screws where drilled at and angel of 90°tangental to the fiber direction with a diameter of 7 mm. The gluing of the screws where made in three different depths and where later exposed to pulling forces. The results showed both pulling breaks and screw breaks when they reached their maximum capacity.

Thesis purposeThe study aims to examine the effects vertical and horizontal line extensions might have on the total parent brand equity in terms of strength and its baseline product regarding of market share, loyalty and penetration under an elapsed period of time. The study aims to investigate a number of actual conducted line extensions effect on the above mentioned aspects of Kellers (1993) definition of brand strength as a part of the total brand equity. MethodologyThe effect of a number of line extensions of the parent brands and the baseline products is being examined in terms of market share, loyalty rate, cannibalization and market penetration. The thesis is focused on the correlations between these different parameters during a certain elapsed time ratio in order to test our theoretically routed hypothesizes in a deductive manner. Occasional correlations are derived from an indexation of data collected from the Gfk database.

Oestrus in dairy cattle has changed over the last decades, the duration has decreased and the intensity of oestrus has declined. A possible explanation can be their high and increasing milk production. Heifers ability to show oestrus is probably not affected to the same extent. The aim of this study was to estimate and compare oestrus duration and strength in heifers of the Swedish Red and Holstein breeds. Standing oestrus has been the primary oestrus sign during many years.

Cement manufacture accounts for 3-5 percent of total global carbon emissions. There is a growing interest in reducing the environmental impact and conserve limited natural resources. In cement production, clinker productions consume 87.5 percent of the total energy consumed in the cement manufacture.Cementa has since many years, focused on reducing the environmental impact of cement production. The work has involved the entire production process from selection of alternative fuels to the development of cement with less clinker content. During 2013/2014, two new types of cement (Bascement and CEM II / B) will be introduced to the Swedish market.

Term: Spring term 2007Study objects: Reitan Servicehandel AB, Vi-butikerna, ICA Sverige ABPurpose: The purpose of this study is to analyse how procurement is used as a strategy to achieve better competitive strength, within the retail food industry.Theoretical: The theoretical chapter illustrates different procurement organisations, multiple and single sourcing, brand equity, consumer behaviour and involvement, Efficient Consumer Response including supply chain and category management and finally Demand Chain Management.Method: For the case studies, three food retail companies have been interviewed: Reitan Servicehandel AB, Vi-butikerna and ICA AB. To illustrate how consumer behaviour influences retail food market, several secondary consumer research studies have been analysed.Conclusions: The results indicate that the procurement organisation can achieve a better competitive strength by a centralised organisation, which make it possible to improve conditions of terms when ordering higher purchase volumes. The sourcing strategies can improve a company?s power within the supply chain. All companies within the study had a very good knowledge about consumer behaviour.

In this study I investigated whether the strength in the manual response for emotional and neutral stimulus search arrays can explain some of the difference in reaction times (RT:s) for emotional stimuli, or not. Earlier, perceptual, cognitive and attentional processes has mostly been used to explain the variance in RT:s. Thirtythree individuals were asked to, as fast as possible, detect a target picture among distractor pictures in 3 rows x 4 columns arranged search arrays. The pictures were categorized in fear relevant animals (snake, spider) and neutral animals (cat). The results showed, more correct responses for cat target.

This technical report describes the master thesis in material engineering called ?Testing of surfaced hardened materials conceivable for gears and shafts?. The work extents 20 academic points. Land systems Hägglunds manufactures and sells different kinds of combat vehicles and terrain vehicles. Since the demands for bigger and stronger vehicles increases all the time, so are the demands on shafts, gears and other transmission details.

This report is the written documentation of a project work carried out at the Division of Engineering Materials at Luleå University of Technology in cooperation with Seco Tools AB. The project deals with the analysis of residual stresses in Ti-Al-N thin film grown on WC/Co cutting inserts. The composition of Al varied from 0% up to 75%. Increasing the Al content in the Ti(1-x)Alx N compound improves the compressive residual stresses even after annealing of the material. The experiments have been performed in a high temperature x-ray diffractometer (HTXRD) where the interplanar atomic spacing was determined in-situ and subsequent converted into stresses.

The thesis project is accomplished during winter and spring 2008 at Karlstad University at the faculty of technology and science. The tutor at Karlstad University is Nils Hallbäck and the examiner is Hans Johansson. Rolls-Royce at Kristinehamn in Sweden is the initiator for the project. The thesis project title is design of the blade bolt joint on Kamewa CPP. CPP stands for controllable pitch propeller.