As an amateur it can be difficult filming from several angles at the same time as this requires several cameras. It´s also hard to film at occasions when it´s not appropriate to manoeuvre the camera manually. Systems for solving these problems already exist, but it´s either more expensive, professionalsystems or cheaper systems with limited functionality.The purpose of this project is to develop a cost efficient solution to the problem above that offers a better functionality then existing commercial systems. The biggest difference from existing products is the wireless video feedback from the camera to the remote unit.The result of the project is a system consisting of two units, a manoeuvre unit with a cradle for the video camera and a remote unit from which the operator can control pan and tilt of the video camera.Communication between the two units is wireless.On the remote unit there is a joystick and a display mounted. In addition to this, there is also an IR receiver that is capable of reading the signal from the cameras own remote and sending it to the manoeuvre unit.The manoeuvre unit is equipped with one motor to control the tilt function and one motor to control the pan.

Lansen Technology develops and sells alarm systems. The communication between the system devices are wireless. The radio protocol used by the system is developed by Lansen with the purpose to be energy efficient. The alarm systems target groups are individuals, businesses and government agencies. The current system is installed, configured and controlled from a control panel for all audiences.

Examensarbetets frågeställning berör användarnas medverkan i Requirements Engineering (RE). Under RE-fasen skall samtliga krav på det kommande systemet tas fram från intressenterna. En viktig intressentgrupp i kravutvinningsarbetet är de kommande användarna av systemet. Resultatet av RE-fasen är en viktig faktor som påverkar hela den fortsatta utvecklingsprocessen samt hur lyckat det slutliga systemet blir.Detta examensarbete innebär en undersökning av vad användarrepresentanterna anser om use case-modelleringen i RE-processen. Undersökningen har påvisat att användarrepresentanterna är positiva till use case-modellering som arbetsmetod för att kartlägga kraven.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

During the spring semester 2012 Robin Westlund has accomplished ?Controlled interaction for more creative meetings - Summit Flexiwall? with the individual focus on social communication based on visual interaction in future office. The project was a part of the course Degree Project for degree of Bachelor of Science in Innovation and Design Engineering (MSGC12) which includes 22,5 ECTS Credits. The course is a part in the program Innovation and Design Engineering program within the Faculty of Technology and Science at Karlstad University.Assigner of the project was Moelven Eurowand AB with their head office in Örebro. The company manufactures and assembles entire room solutions for offices.

Problem: Our opinion is that it is important to consider about usability in system development. In this thesis we will focus on usability in point-of-sale systems. The point-of-sale system we base this thesis on is Extenda Retail. Our case study is performed on Ica Kvantum in Bromölla, which implemented Extenda Retail about two years ago. Purpose: The purpose of this thesis is to figure out what important factors there are to consider, in usability aspects, when developing point-of-sale systems, with focus on the cashier.

The Pedagogical progression within MSI ? Based upon The Bologna Process and UPC.In a near future several of the European countries will begin working after new guidelines concerning a declaration called the Bologna process. Everything will be done one step at a time and the declaration will change the way the students are being graded, all this for the sake of making the European labour-market moreopened for all of its millions of students.In Växjö this process is in the making, but to adapt to the future demands the school must also change its ways of teaching.To increase its quality the University has put together a procedure of actions to improve the pedagogical working method in all its institutions. In this essay we would like to elucidate how the work with the Bologna process is proceeding within the institution of Mathematics and System Engineering and whatthey do improve their pedagogical teaching. By doing a qualitative case study on the student at the Computer Science Program we wish to find the answers to our questions..

In the middle of Australia there is a city called Alice Springs. The city has one of the highest amounts of daily sunshine hours and sun irradiation in the world. The Australian Government runs a project called Solar Cities, and Alice Springs is one of the participators. The main part of the goal with the Solar Cities project is to increase the amount of electricity generated by solar power and by doing that lower the impact on the environment. This thesis examines the possibilities for construction of a large scale solar power plant in Alice Springs. This is done to determine the potential of creating a more sustainable energy system in the city.

A large amount of our time is spent indoors in an artificial climate. To make the experience pleasant there are requirements on the ventilation and the heating system. At the present time the most common form of heating is a radiator system complemented with a ventilation system. A ceiling heating system with combined heating and ventilation can replace the two separated systems. The benefit with a ceiling heating solution is that it saves space since the radiator system is no longer needed.

Many research reports mention the fact that a huge number of all system development projects never reach a successful ending; with other words never fulfil formulated goals. By identifying and forming success factors (and in some aspect risk factors) that the project manager in practice can use, this study may be seen as a step in the direction towards minimising the high number of failed system development projects. The purpose of this research report is to investigate how a system development project, where the development process is based on a specific development or process model (in this case the Waterfall model), can and should be driven. I aim to clarify what is demanded of a project leader for the specific development process and give an account for which eventual leadership qualities that can be well suited for given situation in relation to the need for technical competence. Among other things the project manager should inspire confidence, drive, be a decision maker, engage and own some form of basic knowledge in the field of system development.

When a disaster occurs the main focus is on the loss of human lives. Here the environmental effects have been in the centre of attention. This work has had two main purposes. The first one was to formulate attributes, variables that together present a complete picture of the consequences that an event has had on the environment. The other main purpose was to investigate how people value the impact that a disaster can have on the environment.

This degree project is made for Sundbyholms Golf&Country Club in Eskilstuna. The aim of the report is to produce a website which include a golf course interactive guide and an online game. Programs that have been used during the project are Adobe Photoshop, Macromedia Dreamweaver, Macromedia Director, Discreet 3DS Max and the plug-in 3DS Max Exporter. The choice of programs are based on experience and knowledge from the university education Media and Communication Engineering at Linköping University. The golf course guide contains a 2D-guide (image) and a 3D-guide (interactive image).

Scania Top Team is a competition where the best mechanics in the world are competing against each other. In 2011, the world final was recorded and this material is now used to see which problem solving strategies these top of the line teams are using to solve the realistic problems assembled in front of them. To help them, the mechanics are allowed to use two of Scanias IT-systems: Scania Multi and Scania Diagnose and Programmer 3. This report consists of two parts. The first part is the development of a method to analyze the recorded material.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

Syftet med detta examensarbete är att utifrån ett lönsamhetsperspektiv analysera konceptet ModernaHus och hur det ska möta marknadskraven för flerbostadshus på den svenska marknaden..