This study has examined if importation of waste for energy recovery can reduce the climate impacts of Waste Management Systems. Using Systems Analysis this study will try to examine the complex waste systems in a systematical and strictly logical way to see how these systems interact and affect each other. Specifically examining the climate impact of waste management systems in England. The traditional way of handling waste in England is through Landfills. Land filling leads to emissions of the greenhouse gas Methane. The EU has put in place a landfill directive that is supposed to lead the member states away from land filling as a method of waste management. Today in Sweden there is a competition for the waste available for incineration. The worsening economical situation together with less product packaging and an increase in source separation leads to a lack of waste available for incineration.

The purpose of this study was to describe senior nurses? expectations concerning how a digital information and communication technology systems (ICT) can contribute to the improvement of care leadership and how it can strengthen ties between the school's theoretical world and the practical clinical work-based training (WP) in nursing. The study has a descriptive design with a qualitative approach. The study involved seven leading care nurses. Data were collected through semi-structured interviews.

the most obvious problem at Traction today is the in-between handling that demands much time and resources. The reason is that the packages are not designed with handling in mind. Several of the packages of today also have a poor degree of utilization that means there is room for a fewer number of articles. That in turn means more packages, more transports, more storage space and more staff. On the basis of a specification of demands ? which take quality and environmental influence, as well as transport, handling and economy in account ? we have developed suggestions on new packages that will facilitate handling and lower the total costs, The time of handling will in some cases abbreviate to just a few seconds with the new packages.

In industrial control systems PID-control remains the prevalent strategy, also for processes that would benefit from model based control. The purpose of this thesis is to evaluate whether model based control can be readily implemented in an industrial control system. To this end a simulated surge tank with a simulated industrial control system is studied. For evaluation two scenarios with specified objectives are selected.Following a review of LQR and versions of MPC, Predictive Functional Control (PFC) is considered the most suitable for implementation. PFC is a form of MPC developed with industrial applications in mind and therefore has several advantages for implementation in an industrial control system.

When constructing a new house many questions appear, from architecture to decisions regarding installations. Sweden is situated in a cold part of the planet and questions regarding which heating system to install face everyone who decides to build a new house. This thesis describes a construction solution of a villa in Kiruna. The extended essay analyzes which heating system is most suitable for the construction. The options are geothermal, district and pellet heating systems.

no abstract available.

The basis of the study lies with a newly patented gearbox by cardiologist and inventor Stig Lundbäck. Stig founded CorPower Ocean AB to further develop the gearbox to be used in a wave energy device. The purpose of this project is to develop a concept of a lifting system with CorPower Oceans gearbox that is more energy efficient than a hydraulic lifting system. The goal is to use technology from CorPower Oceans gearbox inversely to perform heavy lifting as an alternative to hydraulics. The project is limited to applying the gearbox and gear rack on a forklift with a lifting capacity of ten tons.The main tool in this project will be the product development process Systems Engineering where only the most relevant parts will be used to develop a concept.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

In past decades information technology has changed the conditions of organizations, not at least within the industry. Advanced IT systems have become a fact in order to cope with rapid changes in the market and to effectively manage an organization?s knowledge. When organizations became more flexible and customized expectations from customers and stakeholders also become higher. These expectations and guidelines are documented in a company?s management system, which can be designed differently depending on what standards the company chooses to implement.

This study is intended to give an impartial view of a young and complex program in Sweden titled Product Innovation Engineering program. The purpose of this program is to increase innovation capability in Sweden that will result in new companies, patents and economic growth. The results from this study might give some direction to future innovation initiatives, but should primarily serve as a tool for the PIEp participants. The study will focus on investigating the creation of the program as well as the development of its strategy. From weaknesses and strengths within the strategy of the program the study should also attempt to show its future potential.

Real-time systems are required to answer to external stimuli within a specified time-period. For this to be possible, the systems behaviour must be predictable. The use of active databases in real-time systems introduces unpredictability in the system, e.g. due to their use of active rules. The behaviour in active databases is usually specified in ECA-rules.

Real-time systems are required to answer to external stimuli within a specified time-period. For this to be possible, the systems behaviour must be predictable. The use of active databases in real-time systems introduces unpredictability in the system, e.g. due to their use of active rules. The behaviour in active databases is usually specified in ECA-rules.

Real-time systems are required to answer to external stimuli within a specified time-period. For this to be possible, the systems behaviour must be predictable. The use of active databases in real-time systems introduces unpredictability in the system, e.g. due to their use of active rules. The behaviour in active databases is usually specified in ECA-rules.

Real-time systems are required to answer to external stimuli within a specified time-period. For this to be possible, the systems behaviour must be predictable. The use of active databases in real-time systems introduces unpredictability in the system, e.g. due to their use of active rules. The behaviour in active databases is usually specified in ECA-rules.