Vattenfall district Heating power plant in Uppsala produces district cooling with absorption heat pumps which leads to a large amount of waste heat that has to be cooled with evaporative cooling towers. The Environmental Court has ordered Vattenfall to survey the possibilities to recover the heat, which is the focus of this thesis.The study begins with an overview of the system, and conditions and limitations for waste heat recovery is examined. In the next step alternatives to recycle the heat is evaluated, either by direct recovering or by upgrading.First, the technical possibility of each alternative is discussed, and then the operation time and the amount of recovered heat is calculated. Those alternatives which are possible are brought further to an economic analysis.The cost of investment for each alternative constitutes the basis for a present value analysis. The results are put together in a table where the total amount of recovered heat is compared with the present value for the different alternatives.

This thesis work is the last part of the Master of Science education inmechanical engineering at KTH, Stockholm.The aim of this project was the development of a Multi-zone modelfor NOxformation in Diesel engines. Because of the stringent emissionlegislations, great effort is made to decrease the fuel consumption and theharmful emissions of internal combustion engines. Computer simulationsplay a decisive role in this context because they substitute the expensiveand time-consuming laboratory tests.The model is based on a multi-zone approach and uses the wellknownExtended Zeldovich Mechanism which gives a relation to calculatethe NO formation rate using the concentration of different gas speciesinvolved in the process.All the most important phenomena involved in the Diesel combustionhave been modelled. A special attention is then paid to the equilibriumconcentration calculation; this is a significant part of the model whichstrongly influences the following steps.A Simulink model has also been developed. This second version isbased on the previous model and it is made especially to allow theconnection with other external softwares, GT-power in this case.

The purpose of the project has been to work out recommendations that reduce the energy-related costs and environmental impact of HPW Fresh & Dry Ltd., a fruit drying factory in Ghana. The factory produces electricity with diesel and biogas but also purchases electricity from the national electricity company. Heat for the drying process is produced from biogas, kerosene and solar panels. In the project the energy system was analyzed by measuring production and consumption of heat and electricity. The project results show that the factory can become self-sufficient on heat if the available energy is used more efficient. The production units for both electricity and heat have low efficiencies.

In the last decades, lean production has proven to be one of the most important organizational paradigms in manufacturing. The lean concept has also spread into the service industry where it is applied within a range of different areas. The wide applicability of lean principles has spurred the authors of this study to apply the principles in the context of the operations of a Swedish remand prison. The thesis examines the process a client of the remand prison Häktet Kronoberg goes through from the time of arrest until he/she is released or convicted and transferred to jail. Based on lean tools and principles, the thesis maps and analyses this process.

Vårt mål med projektet var att göra en webbapplikation åt Gourmet Grön och deras nya produktserie. Applikationen innehåller information om produkterna och hur de används samt vilka fördelear dessa ger..

?Halmstads Fastighets AB? is a local real estate company investing in sustainable development. One problem though is that the domestic waste, particularly the source separation, at the three resident blocks for students? isn´t working very well. This creates inconveniences for people and environment as well as decreasing the impression on the estates.This project has had the ambition to improve the domestic waste and increase the amount of source separation at HFAB´s student hostels.

Livscykelanalys används som metod för att undersöka produkter eller tjänster från ?vaggan tillgraven?. Med hjälp av mjukvaruprogrammet SimaPro utförs en livscykelanalys på förbränning av avfall med energiutvinning. Resultatet jämförs med en livscykelanalys som utförs på biogasproduktion från matavfall, för att visa vilken av processerna som har mer positiv påverkan på miljön. Resultatet visar att förbränning av avfall bidrar till minskad miljöpåverkan med 63,9 kg CO2-ekvivalenter per ton avfall.

The population growth and urbanisation in low-income countries bring issues of poor living standards and miserable sanitation conditions onto the agenda. If well-functioning waste management systems were developed, this could master some of the problems. The already existing local informal waste handling system that is common in many low-income countries, needs to be developed with proper sorting and composting solutions to decrease the environmental burden and improve the overall situation in the dense cities. This master?s thesis project is performed with the intention of developing functional decentralised waste management units in the city of Pune, India.

At SIA TallOil's pellets factory in Latvia wood shavings and saw dust are dried with flue gases from a gas burner. TallOil wants to replace the gas with a biofuel that is available at the pellet plant. The reason for this is the unstable gas market in Europe in combination with the fact that TallOil wants to improve its profile as supplier of renewable bio fuels. In this project the technical and economical possibilities for a fuel conversion to ether bark powder, wood shavings or wood powder have been investigated. These fuels should be burned in one of the following applications: TPS BioSwirl, VTS Multifuel burner or Saxlunds bio fuel combustion plant Due to the fact that the fuel alternatives available are relatively common except for bark powder, the work has mainly been focused on bark powder.

Pulp- and papermills expend vast amounts of water in order to produce pulp, paper and cardboard. Hence, they alsocreate vast amounts of waste water which has to be cleaned before it can be released into the receiving body of water. Insuch a wastewater treatment plant, tremendous amounts of energy are expended by the aeration in the biologicalcleaning process. This aeration is necessary to supply the microorganisms that shall decompose organic material withoxygen, which they need for their metabolism. The transfer of oxygen from the gas phase to the liquid phase isprimarily inhibited by surface-active substances in the waste water like resin acids or fatty acids.

Vårt mål med projektet var att göra en webbapplikation åt Gourmet Grön och deras nya produktserie. Applikationen innehåller information om produkterna och hur de används samt vilka fördelear dessa ger..

As a part of the fight against the global warming the energy production needs to be more efficient and redirected towards sustainable options. One alternative is cogeneration, which means that electricity and heat is produced in one plant. The purpose with this survey is to examine if there are any commercial available combined heat and power techniques, based on combustion of solid moist biomass, which are suitable to small-scale applications. The technique must be able to produce between 2 and 10 MW thermal and the heat demand is a Swedish district-heating system. When already published reports had been studied, the Organic Rankine Cycle (ORC) was chosen as the most suitable technique.

In the production of pulp, paper and cardboard, a large amount of water is used daily. The water has to be purified in the internal purifying plant before it reaches the receiving body of water. In the biological purifying stage at the Stora Enso Skoghall mill, an aerated basin is used where the microorganisms, using oxygen, oxidize the organic material to carbon dioxide. The air is pumped from the bottom of the basin and the oxygen can then be transported from the air bubbles to the water through diffusion. The problem with aeration of waste water from the forest industry is that wood residues, such as fatty acids, are making the transport of oxygen in water more difficult.

The report comprises two separate parts:part 1:  Temperature needs for district heating in the paint shop for axles in building 210part 2:  Energy and low temperature waste heat solutions in heating and cooling systems for   building 64 with surroundingsThe paint shop for axles in part 1 has air quality requirements in places for coating of axles. Toachieve desired air properties there are different process ventilation systems, which consist ofventilation coils for heating and cooling, plus air humidifier. The ventilations coils for heating usedistrict heating. Today the ventilation coils use water of 100°C to achieve necessary air demands inthe coating boxes. This part of the report investigates whether the existing system would achievethe air requirements with a water temperature of 75°C instead of 100°C in the ventilation coilsduring the coldest parts of the year.

An excessive input of nutrients to lakes and other water bodies has created a problem with eutrophication in Sweden. Untreated, or partially treated, domestic sewage is a major source for discharge of phosphorus (P), which is the nutrient most frequently responsible for eutrophication of most fresh waters and the Baltic Sea. The waste water can be cleaned by filter materials, which have a high P-retention ability and which after saturation may be used as fertilizers. Four potentially suitable filter materials were tested in batch- and column experiments in this study. In the batch experiments, the following materials were shaken with waste water in time series ranging from 5 seconds to 60 minutes: coarse (1-4 mm) and fine (0-2 mm) Polonite® (heated bedrock from Poland); Filtralite® (light expanded clay aggregates with limestone added before burning); water cooled blast furnace slag (BF-slag) and BF-slag mixed with 10% burned limestone.