It is essential to reuse- and recycles residues to decrease the amount of deposit materials and reach sustainable energy use. Two ways to work towards this is to recycle wood ashes to the forest as nutrient compensation and extract biogas from combustion of biomass.The aim with this study was to decide whether wood ashes that been used for biogas upgrading with accelerated carbonation also can be used as a nutrient compensation in the woods according to recommendations from the Swedish Forest Agency (Skogsstyrelsen).The ashes that were used in this study came from Johan Andersson who works at JTI in Uppsala, who also treated the ashes with biogas. The ashes have, in both untreated and treated condition, been analyzed in this study according to contents of elements, leaching properties, hardening properties and contents of crystalline phases, to evaluate what impact carbonation with biogas has on the ashes.The accelerated carbonation led to hardening of the ash, and decreased amount of CaO- and increased amount of CaCO3. The CO2-uptake also entails a dilution of the elements, and the content of nutrients and trace elements decreases. However the results show an indication of an uptake of S from the biogas to the ash, since the dilution had a smaller impact on S than the rest of the elements.

A one-cylinder research engine has been used for studies with a Diesel Dual Fuel concept (DDF). DDF is a concept that utilizes a pilot diesel injection to ignite a homogenous natural gas/air mixture. Emissions and engine efficiency have been analyzed in an emission cycle called European Stationary Cycle (ESC) and the knock/pre-ignition problems with this type of engine have been investigated.At low and mid torque levels, an early diesel injection around 60 crank angles degrees (CAD) before top dead center (TDC) was used. At these loads raw NOxemissions was below EURO 6 level (0.2 g/kWh). NOxwas at EURO 5 level over the complete ESC without after treatment and with SCR at high loads it should be possible to reach EURO 6.One issue with DDF is the high HC emission levels.

Ungefär en tredjedel av maten som produceras i världen slängs. I Sverige slängs över 1,2 miljoner ton mat varje år. En stor del av det är så kallat matsvinn, onödigt matavfall som skulle kunna använts om den hanterats annorlunda. Matsvinn påverkar miljön och samhällsekonomin med förluster genom hela livsmedelskedjan och genom den avfallshantering matsvinnet ger upphov till. Matavfall kan användas för produktion av biogas, kompost och värme men det är bättre att reducera produktionen än att återanvända eller omvandla produkten. Svenska skolkök slänger runt 30 000 ton mat varje år, varav drygt hälften beräknas vara matsvinn.

Pappersmakulatur uppstår i tryckpressarna, men orsakerna finns i företagets alla funktioner. För ett framgångsrikt förbättringsarbete med att minska makulaturen krävs därför att all personal är engagerad.Examensarbetet utfördes på Bobergs Tryckeri AB i Falun, ett familjeägt företag med 60 anställda, som producerar personifierad direktreklam och blanketter. Syftet var att undersöka hur pappersmakulaturen kan minska och målet var att hitta orsaker samt ge förslag på åtgärder för att minska den.Genom intervjuer med personalen kartlades produktionssprocessen och utifrån det utarbetades förbättringsförslag. Exempel på förbättringsförslag är att kontinuerligt mäta och rapportera makulaturen, förbättra kommunikationen mellan avdelningarna och utveckla färgstyrningen. Litteraturstudier och kontakter med nyckelpersoner inom branschorganisationer och andra liknande företag, var till stor hjälp i arbetet.

Mitt examensarbete fra?n Designprogrammet ? ha?llbar utveckling, a?r en under- so?kning av flera dimensioner. Det o?vergripande arbetet a?r ett platsspecifikt insamlande av framtida visioner hos inva?nare, kommun och kreato?r. Visualiseringen involverar samtliga av de ovan na?mnda parterna i skapandet av en ny mo?tes- plats i ett medialt kategoriserat miljonprogramsomra?de.

In this work an assessment of the compressed air system in the facilities of Vattenfall Heat Uppsala has been conducted. The facilities constitutes, among others, a combined heat and power plant, and two waste incineration plants. The compressed air is supplied primarily by seven rotary screw compressors and yearly electric energy consumption in these has been determined. Furthermore, the usage of compressed air has been mapped in order to find processes with energy savings potential. Several suggestions how to reduce the usage of compressed air have been presented, resulting in decreased need of electric energy and reduced CO2-emissions.The results show that total need of electric energy in the compressors, during a standard production year, amounts to 5.83 GWh.

The Anglo-Saxon trust is not a new phenomenon, but existed as early as in the Middle Ages. The concept is customary among common-law countries, such as England the US,but unfamiliar to civil-law countries like Sweden. The person who creates the trust is called a settlor, the one who holds and administer the property is a trustee and the person who benefits from the settlement is called a beneficiary.In Sweden there is no legislation of how the trust ought to be assessed, but the need to understand it has probably increased with the internationalization.The Swedish Supreme Administrative Court has had a few opportunities to elucidate some of the uncertainties regarding trusts, but chose to abstain. With this The Swedish Tax Panel has very limited guidance from the court when they receive an application of an advance notice.A trust is not a legal entity nor a tax subject. This differs the trust from a foundation and they can not be placed on an equality from a Swedish tax perspective.In an advance notice, 2010-03-23 (dnr 103-09/D) om Inkomstskatt: Inkomst av tjänst ? värdepappersförmån, the Swedish Tax Panel equalizes the trust property with shares when determining how to tax the assets.

In this thesis we focus on the issue of crowdfunding and especially how a project relates to and embraces its community. While a lot of related research focus on what makes people give, our research instead delve into whether a creator looks upon the sponsors as something more than just a financial resource. To manage this task we used a triangular perspective consisting of a case study, a questionnaire and a netnographic study. The goal was to gain the perspectives of creators, crowdfunding platforms and sponsors on how the communication between the community and the project works and can be improved.       The three crowdfunding platforms we reviewed (Kickstarter, IndieGoGo, Rockethub) all had fairly similar models on how to attract sponsors and make them involved in the project, while the questionnaire and netnographic study demonstrated how a community could contribute in different ways.

The purpose of this study is from a case study develop a model that aims to cost effectively improve productivity in a manufacturing production process. The study highlights the importance of having knowledge about customer needs and using a holistic process perspective when improving productivity to identify the relations between the process stations and by this find problems that cause waste and losses in productivity. Tools and methods used to make production more efficient such as single minute exchange of die, spaghetti diagram, 5s and master production schedule is presented an applied in the model to see how these effect costs, productivity etc.Maintenance effects on quality and productivity in a manufacturing company will as well be covered in this thesis. The results and conclusions finally reveals how the process improvement tools, maintenance and production planning for example effects each other and why it is important to establish an attitude in the company where continuous process improvement should be emphasized..

The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

Hemp is a versatile plant with many uses that has been around for thousands of years. The plant is highly adaptable andwill cultivate in almost any soil. It has excellent remediation properties and has shown to be relatively consistent when itcomes to crop yields. The aim of this literature survey is to examine how hemp can be used to be considered asustainable energy crop in Sweden through database searches and interviews. Hemps characteristics as an energy cropand its remediation properties is evaluated and compared with other plants that are used in Sweden.

Within agriculture it is important to optimize the use of nitrogen, not only from an economic point of view but also to minimize damage to the environment. This can sometimes be difficult, especially within organic farming. Organic farmers are using increasing amounts of waste products from the food industry to cover their nitrogen needs. These different organic fertilizers release nitrogen at different rates and under specific soil conditions. Because of this, it would be beneficial to have a standardized method to measure the amount and rate of nitrogen mineralization from organic fertilizers. This project contributes to this knowledge by investigating whether relatively simple and repeatable laboratory methods can be used to estimate the nitrogen fertilizer value of organic fertilizers.

Pappersmakulatur uppstår i tryckpressarna, men orsakerna finns i företagets alla funktioner. För ett framgångsrikt förbättringsarbete med att minska makulaturen krävs därför att all personal är engagerad.Examensarbetet utfördes på Bobergs Tryckeri AB i Falun, ett familjeägt företag med 60 anställda, som producerar personifierad direktreklam och blanketter. Syftet var att undersöka hur pappersmakulaturen kan minska och målet var att hitta orsaker samt ge förslag på åtgärder för att minska den.Genom intervjuer med personalen kartlades produktionssprocessen och utifrån det utarbetades förbättringsförslag. Exempel på förbättringsförslag är att kontinuerligt mäta och rapportera makulaturen, förbättra kommunikationen mellan avdelningarna och utveckla färgstyrningen. Litteraturstudier och kontakter med nyckelpersoner inom branschorganisationer och andra liknande företag, var till stor hjälp i arbetet.

Lean has been studied intensely since the 1980s and it has been tested and successfully implemented in a wide variety of businesses. This thesis aims to examine the potential effects of a Lean implementation on meeting efficiency, a topic that has gotten little attention in the research community. First, a number of meeting problems are introduced, as they are perceived from the company that is the subject of the study. Second, the potential of introducing Lean in a meeting process is evaluated using the Lean Thinking principles. Third, the wastes that are generated from the meeting problems are identified.

The control of indoor temperature must be able to handle large time constants and both measureable disturbances like outdoor temperature, and non-measurable disturbances, like waste heat from appliances. Due to cheaper microcontrollers (small computers with designated tasks) with better performance, more advanced and computation-demanding methods for control can be used.In this thesis, Generalized Predictive Control (GPC) has been implemented and tested on a theoretically derived model of a house. GPC states that a model of the system is estimated in every sample, and the control is carried out simultaneously, based on predictions of the model. Disturbances like solar radiation can be estimated and used in the control as well. The control signals are determined by quadratic programming, which makes it possible to consider conditions, for example limitations on the control signals.GPC requires a number of parameters to be defined, like model order and control signal penalty, but is relatively robust for variations in them.