AbstractResource efficient manufacturing is a term that has been increasingly applied within manufacturing, where one of the key points is to reduce waste of such forms that do not add value for the end customer. By the Lean principles, there are seven plus one types of waste, in which the definition of the eighth point varies among sources. In this study, the eighth type of waste has been interpreted as the untapped creativity and competence among employees that has not been put to use. From this, our question was incubated; How can you make the most of the employees? untapped creativity and potential within manufacturing? The case study will be developed with empirical data obtained from Dometic Group by conducting interviews.From the gathered literature, it was concluded that the communication between employees contributed to an increased understanding of one another as well as it allowed for improvement in work.

Every year, KTH participates in the Shell Eco Marathon, a competition whose goal is to design a vehicle that can go as far as possible using only the equivalent energy of one liter of petrol fuel. This year, one of KTH?s contributions to this race is the Agilis prototype; a car powered by a uniquely configured HCCI-engine developed at the university. The engine is dependent of several subsystems in order to work properly, among other, systems for cooling and lubrication.Combustion engines are in need of a cooling system that reduces the heat developed during the combustion. In general, two main types of cooling systems are employed; either air cooling, where the outside of the cylinder is exposed to a flow of the surrounding air, ore water cooling, where water flows in tubes around the engine, and the heat are transferred by the water to the surrounding air through a heat exchanger.The purpose of the lubrication system is to prevent the friction that builds up in the interference between moving parts in the engine.

In the pilot plant at Hammarby Sjöstad, Sjöstadsverket, several new methods are tested in order to achieve a good use of resources. When a new technique is considered it is often the performance of the technique itself, under given conditions, that is evaluated. However, in order to evaluate the overall function the whole picture is needed. With a system analysis it becomes possible to make a comparison where all the positive aspects are put up against the negative ones, for the technique itself as well as its requirements. In this way the influence that minor components have on an entire system can be considered.This report presents a system analysis of an anaerobic membrane reactor (MBR) with a VSEP-membrane (Vibratory Shear Enhanced Process).

As a small and land scarce country, effective waste management is ofoutmost importance in Singapore. In this study the production of biogasthrough anaerobic digestion from the organic fraction of municipal solidwaste (OFMSW) was compared to incineration of the waste. At the momentalmost all of the OFMSW in Singapore is incinerated. Three differentscenarios were compared to the reference scenario (incineration): one with alarge scale biogas plant that can treat half of all OFMSW in Singapore, onewith a medium scale biogas plant about 15 times smaller than the large oneand one with a small scale biogas plant that can treat waste from e.g. ashopping center or a food center.By using life cycle assessment (LCA) the different scenarios were comparedin terms of global warming potential (GWP), acidification, eutrophication,energy use and land use.

The municipality of Västervik, with support from Envipro Miljöteknik AB, is carrying out a main study of the minefields at Gladhammar. Mining of iron, copper and cobalt under different periods from the 16th century until the end of the 19th century has led to discharges of metals to the lakes situated downstream. The aim of the main study is to investigate the possibilities to reduce the environmental load on the surrounding ground and water caused by heavy metals from the mine. The present report is a part of the main study. The aim of the work is to investigate the geochemistry of the groundwater.

The biogas plant Kungsängens gård, owned by Uppsala Vatten och Avfall AB, produces biogas and biomanure from organic household waste, food processing waste and slaughterhouse waste. In year 2012, 4.4 million Nm3 of biogas were produced from 25 200 tons of waste. Before digestion all substrate is sanitized by pasteurization at 70°C in order to kill pathogens. Another method, integrated thermophilic sanitation (ITS), is of interest in order to decrease the energy demand. The method implies that the substrate is sanitized during ten hours in the digestion chamber, where the temperature is 52°C.

Trioplanex International AB is a part of the group Trioplast Industrier AB, which produces packaging materials for the film and hygiene industry. The group is active throughout Europe, where most of the production is located in Sweden, with head office in Smålandsstenar. Operations in Landskrona consist of Trioplanex International AB and Trioplast Landskrona.Semi-finished articles consisting of paper cores, so called bobbins, give rise to a high amount of core waste in any form of core cutting. The objective of the report is to map out all core waste and illustrate the material flow with regard to present layout and equipment.In the beginning of the project an analysis of the current process was carried out with focus on the cutting equipment. A case study in the form of an improvement work took place in order to reduce the causes which had the biggest impact on existing machinery.Improvement proposals were discussed by the author together with supervisor, assigner and other parties involved.

In 1994 the EU directive of packaging waste was adopted. The result was that all EU member states developed different systems to manage packaging waste and recycling. This paper examines the various systems and the factors that affect the level of recycling. This is done by a cross-sectional study between countries. The results of my study suggest that take-back system generates less recycling than other systems, the mandatory deposit system can affect the recycling in a positive way.

The biogas plant Kungsängens gård, owned by Uppsala Vatten och Avfall AB, produces biogas and biomanure from organic household waste, food processing waste and slaughterhouse waste. In year 2012, 4.4 million Nm3 of biogas were produced from 25 200 tons of waste. Before digestion all substrate is sanitized by one hour?s pasteurization at 70°C in order to kill pathogens. Another method, integrated thermophilic sanitation (ITS), is of interest in order to decrease the energy demand.

Open pit mining creates huge amounts of tailings and waste rock deposits. Due to it's content of sulphide minerals, predominantly pyrite (FeS2), there is a risk of oxidation and formation of acid water containing heavy metals, known as Acid Rock Drainage (ARD). To prevent the process of oxidation, the tailings and waste rock have to be reclaimed. The most commonly used methods of reclamation are a coverage of water or soil. Mining also results in a large-scale interference in the landscape that will make an eternal change of its appearance.

Sewage sludge contains plant nutrients and has earlier been utilised as fertilizer to cropland. Unfortunately not only plant nutrients but also heavy metals, pathogens and organic contaminants tend to accumulate in sludge. The suitability to use sewage sludge in agriculture has therefore been subject to several discussions over the years. The Swedish food industry does no longer accept sludge as fertiliser for Swedish producers. In 1999 the Swedish parliament accepted several objectives for environmental protection. In order to prevent environmental pollution and further exploitation of the earth crust, one of these objectives confirm that phosphorous from sewage shall be recirculated to arable land.

The purpose with this project is to compare different fuels when investing in a central combustion station at a case study farm. I have chosen to write about biofuel from an economical perspective. This because the heating costs are steadily increasing. Also because the farm in this case study has several different heating systems, which are neither profitable nor easy to work with. I have made calculations regarding usage of splinter, wood and grain for the heating system.

The aim of this master thesis was to create a dynamic model for the processes in a solid fuel boiler of the moving grate type. Another aim with the model was to keep it as simple as possible but still able to catch the dynamics of the processes in the bedplate of the boiler. The creation of the model had its origin from drying and combustion equations used in earlier modeling work of boilers. The represented model has been used to simulate different kinds of disturbances in a boiler and different ways to control the boiler. These tests show that controlling a number of parameters in the bed of the boiler is an effective way to keep the grate stable during disturbances.

The aim of this thesis is to improve the control of urea injection at the combined power and heating plant Framtidens Gärstad (FTG). Tekniska Verken i Linköping AB is the owner of the plant.The FTG plant consists of a boiler where garbage combustion is done. From the combustion nitrogen oxides are emitted. These nitrogen oxides are hazardous to the environment. To reduce the nitrogen oxides, injection of urea into the boiler is used.

Göteborg Energi has a surplus of district heating during spring, summer and fall. The heat surplus is due to a constant production of waste heat from oil refineries and heat from waste incineration over the year. It would be desirable to increase the demand for heat and the uptime for the newly built combined heat and power generation plant, Rya Kraftvärmeverk. One alternative could be to integrate Rya Kraftvärmeverk with a pellet production facility. By producing heat, electricity and pellet in a joint process the energy use can be decreased.