This essay represents a chronological and contextual analysis of Clay pipes that have been found in the urban settlement of Västergarn during seminary excavations between 2006 ? 2012, conducted by Gotland University. Clay pipes can be dated closely and are useful means for dating and interpreting archaeological contexts from the early modern period, such as house foundations. There have been excavated four house foundations in Västergarn with different sorts of Clay pipes dating to the post-medieval period. Can they tell which people used them or which country they were produced? By discussing the meaning of Clay pipes in early modern society on Gotland this essay tries to answer these questions..

Sewer trenches usually contain material with a higher hydraulic conductivity then the adjacent soil. Thus they can serve as paths of preferential flow in a polluted area. Wastewater from factories can also leak from wastewater pipes and pollute the soil in the sewer trenches.The purpose of this project was to investigate pollutions in sewer trenches and in sewer pipes in the industrial area of Köpmanholmen, 20 km south of Örnsköldsvik in the north of Sweden. To make an estimation concerning the potential of transport of pollutions in sewer trenches, hydrological calculations were performed.Leakage to any greater extent did not seem to be a problem in the area. This is the case both for the concrete and the wooden pipes that have served as factory wastewater pipes.

In this project a washing station has been constructed for Albany International AB. At present, there is no existing system to clean the dirty pipes that are coming back to the company.The work followed the product development process, and it started with the requirements list. This was followed by brainstorming, evaluation and completion.The result was a concept for de present time and one concept for the future.The present concept is intended to be built immediately. This is an adjustable bench with sliding bearings to facilitate the work. The actual cleaning is done with a high pressure washer that uses hot water.

This study intends to examine teacher´s thoughts and perception of esthetic activities at preschools. I have chosen to restrict the esthetic area to the significance and function of clay to the teachers and children. On the basis of the belief that children can, and need access to a variety of ways to express themselves, we used the interviews to take part of teachers work and thoughts concerning clay, and the esthetic work. I have in this qualitative study addressed four questions: How do the teachers use clay in preschool activities? What do the teachers think about clay as a tool in the educational work at the preschool? Are the teachers working from the perception of children?s rights to express themselves in different ways and with the help of different tools? What function does clay fill for the children?I have interviewed eight teachers and taken part of both older and more recent theories around children and the creativity in esthetic contexts.

Shear Strength and Deformation Characteristics of Uppsala Clay with CRS and Standard OedometerTyra Morell Bonin & Magdalena MählerTo see how much a clay compact under different pressure one can use several different methods and in this project, two methods were used, the Standard Oedometer and a CRS apparatus. A Standard Oedometer is a full-time manual device and the CRS apparatus is a modern electric and automatic device. The aim of the project was to see similarities and differences between the two methods and examine which method that were most reliable. This has been done with repeated laboratory tests and afterward evaluations. With this information one can get a picture of how the clay will behave and how it will deform in nature.

Large amounts of phosphorus (P) are lost from the arable land due to water erosion. Both phosphorus attached to particles and dissolved phosphorus (mainly phosphate) are transported away with drainage-water and surface runoff. Good soil structure is important in minimizing these losses. In this study, soils from 50 fields were analysed with respect to aggregate stability as measured by dispersion of clay together with the content of total phosphorus (TotP), particulate phosphorus (PP) and phosphate phosphorus (PO4P) in the water phase. All soils were clay soils with clay content varying between 21 and 54%.

This report is focusing upon relining from a client?s point of view. Potential buyers are given a presentation of the different methods available today together with a general briefing describing the process. An important part of this report are the interviews that took place with already established customers. Property owners, managers, pipe cleaners, and project managers whom all been in contact with relining have answered the questions given along with their own thoughts and have also given recommendations of other persons to talk to.

Most of the city of Uppsala rests on postglacial clay with a varying content of sulphur. The sulphur occurs naturally in the clay in reduced form as sulphide and the clay is for that reason usually called ?sulphide clay?. Excavation during construction activities gives rise to large amounts of excavation material, of which the sulphide clay is a considerable part.When the clay is exposed to air and water, an oxidation of the sulphides occurs which may produce an acid leachate and the mobilisation of heavy metals bound in the clay or underlying material. The aim of the work has been to improve our understanding of the behaviour of sulphide clays and produce a basis for risk assessment in the future handling of excavation material with high sulphide content.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.