The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

In conventional viscose manufacturing, a large amount of carbondisulfide is consumed. This amount has to be decreased to keep the production cost down and to reduce the environmental impact. The purpose with this work was to show if an enzyme treatment of a dissolving pulp could increase the degree of substitution in the viscose so that the amount of carbon disulfide consumed in the process could be decreased. Previous investigations by Kvarnlöf (2007), Engström et.al. (2006) and Henriksson et.al.

Most people have been forced to throw away a pot-plant after its death. There are many reasons to the death of a plant, but mainly it?s because its owner forgets it, and therefore fails to water it. The purpose of this project is therefore to develop a product which can prevent this from happening, while the product has to have a low manufacturing cost to be able to compete whit other, similar, products on the market. During the project, a benchmarking has been done to give a clear picture of what the product has to compete with. The directives there are for CE-marking, and which of these who concerns the product has also been looked up.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

The automotive industry is increasingly studying lightweight solution in their designs, also rational production and low costs in materials and manufacturing methods are of great interest. This thesis consisted in the practical evaluation of anchors for sandwich panels. The object was to study loads of shearing and pull out of the plane. The experiments were carried out on panels made up of 1mm aluminium coatings and 50mm extruded polystyrene (XPS) at its core. As the fasteners used simple methods such as blind rivets, screw and glue.

The purpose of this work is to develop and test a design process where quick decisions and model building has a prominent role. The goal is to develop a number of products and build prototypes to be shown during the Carl Malmsten Furniture Studies spring exhibition 2012. I?m also writing a report describing my work.To reach my goal I have each day during the first phase conducted a short research and found a concept based on that days name day. Then I have continued in the workshop and worked with three-dimensional models.

Detta examensarbete omfattar produktutvecklingen av en komponent till en mätutrustning som ska mäta flytbarheten hos smält metall. Arbetet har utförts hos Bryne AB och har lett fram till koncept-, material- och tillverkningsförslag för komponenten. Arbetet har även utvärderat ett för gjuteribranschen nytt formmaterial som alternativ till dagens gjutsand. Tester har gjorts för att se om återvunnet (material x) går att använda som formmaterial till högtemperaturapplikationer..

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

Because of an increasing demand from customers and changing external environment, there is a need for continuous improvements, for both manufacturing and service organizations, to meet these demands. Manufacturing organizations have been working systematically with quality improvements for a long time, but it has not been as common for service organizations. Because of that the methods to use for implementation of the systematic improvements have not been designed to fit service organizations, and not either for public organizations. The purpose of this thesis is to explain if and why the Swedish Road Administration?s organizational culture and handling of ideas and deviation support an implementation of continuous improvement management.

Title:Pecking-order i små tillverkande företag Level of thesis:Master´s dissertation in banking and auditing Authors:Mathias Klasén and Maria Waderoth Advisor:Joakim Winborg Background:The area of business financing has been well studied during the 1900´s. Many studies and theories are made with big corporations in mind, and the importance of small businesses wasn?t enlightened until the end of the 1900´s. Business financing has created a number of theories, among them Myers pecking-order theory. This theory implies that business managers prefer internal equity in front of debt and external equity.