The energy use in a workshop company has been examined in this work in order to find areas for energy efficiency improvement. The combined oil and electricity heating in the company were compared with other alternative heating systems including cooling of the premises in following combinations:Ground source heat pump for heating and coolingDistrict heating and absorption coolingDistrict heating and low temperate surface water coolingEnergy use, operation costs and carbon dioxide emissions were calculated for the current heating systems and the three alternatives including cooling. The ground source heat pump for heating and cooling decreases bought energy with 34 MWh annually compared to current heating only. The district heating and low temperate surface water cooling has the largest reduction of operation cost and carbon dioxide. The operation cost decreases with 42 kSEK and the carbon dioxide with 43 metric ton CO2 annually.

During the last decades the housing sector has increased continuously, and housings and services accounted for 40 % of the energy usage in Sweden during 2011. The expansion in number of buildings in society has resulted in an increase in both energy usage and emissions of greenhouse gases. It is crucial to enable a sustainable development of society and as a result, the demand to reduce the emissions of carbon dioxide is a current question. In this study, the carbon dioxide emitted from the housing sector in Stockholm is estimated. The housing sector can be divided into different types of houses such as apartment blocks, single-family houses and holiday houses. By collecting information of the energy purchased in respective households, a computational model is generated that calculates the total emission of carbon dioxide.

Uppsats för avläggande av filosofie kandidatexamen i Kulturvård, Konservatorsprogrammet 15 hpInstitutionen för kulturvårdGöteborgs universitet2014:49.

Oxygen consumption and carbon dioxide production are usual measurements within the sports and training physiology. The same measurements are also common when it comes to establish the amount of energy that is used during work and to establish the intensity of work. The volume of oxygen that is consumed contra the volume of carbon dioxide that is produced can be used to calculate the metabolic rate within the human body. This calculation shows the percent relationship between carbohydrates and fat in the metabolism. The first accurate method to measure the breathing gases for use in metabolic calculation was established in the early twenty century when the Douglas bag method was introduced.

In conventional viscose manufacturing, a large amount of carbondisulfide is consumed. This amount has to be decreased to keep the production cost down and to reduce the environmental impact. The purpose with this work was to show if an enzyme treatment of a dissolving pulp could increase the degree of substitution in the viscose so that the amount of carbon disulfide consumed in the process could be decreased. Previous investigations by Kvarnlöf (2007), Engström et.al. (2006) and Henriksson et.al.

Private individuals can voluntarily buy EU Allowances (EUA) in order to remove them from the European Union Greenhouse Gas Emission Trading System (EU ETS). It leads to progressive reduction of total carbon dioxide emissions in Europe. Kalmar Energi offers customers to obtain one EUA (equivalent to one ton of CO2) per year by paying 25 SEK a month as a KlimatEl-supplement. The purpose of this research is to examine the customers? attitudes in the issue of climate compensation and trying to define the reasons behind their choices.The results of the quantitative questionnaire were analyzed by using descriptive and analytical statistical methods and have shown some correlation between customers? ages and decisions to accept or not the offer of KlimatEl.

Biogas is a renewable energy source that is produced by anaerobic digestion of organic mate-rial. In Sweden, biogas predominately comes from sewage water sludge and landfills or from organic waste of households and industries. Small scale digestion plants at farms are espe-cially expected to contribute to increased biogas production in the future. Biogas can be ob-tained directly in it?s raw form and used as fuel in a combustion chamber.

Each year, the coffee machines at Ericsson in Kista produce around 100 tons of ground coffee waste.The companies Coor Service Management, Löfbergs Lila and Selecta are all responsible for differentstages in the logistical chain in delivering coffee and, together with Ericsson, they want to increasetheir environmental benefit. The plan is to produce biogas through anaerobic digestion instead ofincinerating the coffee waste in a heating plant. The results are to be presented as different businesscases in which different biogas plants are compared with the reference case (heating plant),comparing costs and environmental impacts.There are two major environmental benefits from producing biogas; reduced carbon dioxideemissions from when fossile fule is replaced by carbon neutral biogas, and reduced emissions fromreturning digestate from the bio reactor to farmland instead of using industrial fertelizer.In order to determine the biogas potential in coffee waste, a couple of properties had to bedetermined in a laboratory. Properties such as the dry substance content, heating value, moisturecontent and ash content. The results show that 100 tons coffee waste could produce around 16 500Nm3 biogas which would contain 163 MWh.The biogas reactor and upgrade plant both need energy gas to function and uses around 14 MWh ofthe produced gas.

Food consumption generates externalities such as carbon dioxide emissions, which contribute to global warming. The principal issue is that emissions are not covered by the "polluter pays principle". For this reason, new policy instruments need to be tested and implemented to correct the externalities. In food production, beef and dairy production has the largest environmental impact in terms of carbon emissions. As food is a necessity, simply reducing production will not solve the problem.

New high strength steels require improved cold rolling techniques. The aim of this degree project was to develop a new and money saving cold rolling technique to manufacture steel strip for saw blades. The work is based on earlier rolling experiments made with a high carbon steel grade at LuCoil Steel AB. The work also focused on the mill requirements to cold roll high strength steels. The results show that LuCoil?s existing cold rolling mill was actually designed for rolling low carbon steel.

This thesis has the overall objective to develop the optimum sealing system between the retarder and transmission. Today, there is a pressure-relief and two radial seals separation between the retarder and transmission. It has been found that carbon residue formation may occur between retarder axle and seal lips with, in some cases, leakage as a result.We have in this thesis tried to explain the phenomenon of carbon residue, how it is formed and why it can be seen just on the seals? A rig test was conducted where we show how friction, speed, transmission temperature and mitigation phases of the retarder affects temperatures in the sealing environment. Factors affecting the coke structure are reported, together with proposals for measures that provide a mitigating seal environment.

The idea for this project was initiated together with one of the leaders in the forest, paper and packaging industry. To get through an A/R CDM process the company is exposed to the risk of failing the process or that the overall costs will exceed the benefits of the project. This would delete the incentives to invest in GHG removals compared to purchasing emission allowances on the carbon market. The questions that have been raised and needs clarification in the thesis are the following:? From a company perspective, what are the incentives for implementing Forest Clean Development Mechanism (CDM) projects?? What is a likely financial outcome of a reforestation CDM project on degraded land in the Guangxi province of the Peoples Republic of China?? When does an investment like this break even with the cost of buying market based carbon emission allowances? The objective of this master thesis is to carry out a research about the incentives for forest, paper and packaging companies to invest in reforestation through the clean development mechanism.

AbstractElectricity consumption is a globally increasing problem caused by the high share of electricity produced in coal power plants. These contribute to high carbon emissions when only about 1/3 of the heat generate electricity and the remaining 2/3 of the heat cools off. Combined heat and power plants (CHP) have high efficiency because they use the residual heat for domestic heating. The CHP plant often use fuels from renewable resources, giving them a lower carbon footprint, but are also depending on the heat demand. If electric powered products such as drying cabinets convert to heat powered products more environmentally friendly electricity will be produced by CHP plants, which can supplant electricity, produced from coal power plants and reduce carbon emissions.

This report is a thesis for collegeengineering program in structuralengineering at Uppsala University andwas commissioned by the Swedishcontractor Svevia. The study aims toprovide an overview of the mostbeneficial bridge material from bothenvironmental and economic point ofview.The life-cycle analysis covers onlycarbon dioxide emissions, since it isthe most spoken of in today?s climateagenda. Furthermore, this study aims tohighlight which parts, of the systemboundary, that contributes to greatercarbon emissions for the wood- and theconcrete bridge.The life-cycle cost analysis wascalculated with a lifespan of 40 yearsand covers the basic cost of investment,operating and maintenance, anddecommissioning costs.The analyzed constructions in this studyare existing projects that are almostcompleted. Both bridges were designed tohandle loads up to 60 tons.

Unmanned aerial vehicles (UAV?s) are nowadays greatly appreciated. The advantage over manned airplanes are great since UAV?s can be much smaller and therefore lighter. The goal of this project is to evaluate the performance of an environmentally friendly UAV using only lithium-ion batteries.