The producers of grain in Sweden are facing a rough future. The competition is getting harder all the time, in Sweden, in EU and also from the ?world market?. The producers have to be more efficient and have to have bigger units. Many producers might have to look for new alternative production opportunities.

Guazuigua is a small village in Bolivia, which has had too small water resources, especially for irrigation. A project started after some studies were made, to create a canal to provide the village with water from a nearby town. To make the canal work it had to cross a dried out river. There have been several attempts to cross these dried out rivers, but with poor results. The purpose of the report is to provide a solution for this problem.

Upon marketing the system in Europe and the USA cost savings generated from reduced work force have been prevailing. Since the cost of labour is much lower in the Asia Pacific region other factors have to be stressed. The parameters of flexibility and quality assurance may however cover any initial investment in a production system. Our purpose is to value flexibility and quality in a manufacturing context, applied to DAS, in order to use it in investment Calculations. In order to make an adequate estimation of different companies, due to problems associated with acquiring correct figures, the Key Success Factors needs to be examined so that the gathering of numbers can be conducted with more focus.

The dissertation deals with an account of actual problem, which can arise within EMC and power quality. The cause of power interruption and what can be done to minimise the power interruption is discussed. It also includes a definition of planning levels and which factors one needs to have control over to carry out a possible planning strategy and how the local distributions net could be more secure. The electrical net could be secure but no system can be free from interruption.The dissertation examines two distribution transformers: GLA40T1 (Glansås) and T399 in Tranås Energy which don?t have regulators.

The Swedish government have a goal that wind turbines shall produce 30 TWh by the year 2020, compared to about 3,5 TWh produced in Sweden during 2010. To minimize the disturbance that wind turbines create the Swedish Environmental Protection Agency has stated a guideline value that noise from wind turbines at nearby residents shouldn?t exceed 40 dBA, at 8 m/s wind speed. With advanced calculation models, like Nord 2000, the emitted sound from future wind turbines can be calculated at an early stage to optimize the power production without exceeding the 40 dBA. When the turbines have been built there is a need to verify that they really are within the guideline.

This report consists of two parts, out of which the first deals with the planning and designing ofa small house in the Swedish city of Huddinge, using the weather conditions of the Swedish cityof Malmö. The house has to be in accordance with the Swedish building- and constructionregulations, as well as with the limitations in energy consumption given.The house itself has to consist of at least two bedrooms, and blueprints of the house, variousconstructional elements, ventilation, sanitation and electricity have to be drawn. Calculations ofthese aspects also have to be made, to ascertain that the different parts function as they should,and that the dimensions are sufficient.The second part is called ?Allergy free home?, and investigates how indoor climate affects us,and whether it has changed during the last few decades. It also makes an effort to see whetherthe increase of allergies and asthma is correlated with possible changes in indoor climate, andwhether technical solutions might help to handle or even decrease the issues arisen.

According to a decision of the European Commission, measures are to be taken to reduce the use of energy in the EU. The goal is to reduce it by 20 % compared to the current use. This shall be done to the year 2020 (European Commission, 2011). One industry that use large amounts of energy is the construction of buildings which account for almost a third of the energy use (Brogren, 2012). The major part of the energy that is used in the construction industry is not used when the buildings are built, but rather during the rest of their subsequent lifetime.

There exist several known methods for calculation of radio coverage for ground-based systems. As far as we know there are no equivalent methods for the case of flying platforms when the altitudes and speeds are significantly different to those of ground-based systems. This thesis describes the theoretical concepts behind Calculations of radio coverage for flying platforms. An investigation is made to sort out what is important and possible to employ in a model for simulations. A method is described and implemented in a program for evaluation of flying radio systems.

Energy is today a very common topic, not only in Sweden but in the whole Europe. In EU they have given out a directive 2002/91/EG about buildings energy use and throw this they have forced their members to show how much energy their buildings use. In Sweden has the gouvernment established a law (SFS 2006:985) about energy declaration for buildings which demands that the building owner needs to show how much their buildings energy consumption are. Important to know is that this law doesn´t applies for industrial buildings.The report will show what the new law about energy declaration for buildings and appurtenant directions will mean for Riksbyggen. Also energy Calculations will be done to be able to compare Riksbyggen buildings with the new law and directions.

A substation must be properly protected against lightning and other external effects to the equipment in the station or staff, for that we use relay protection. They should also protect against internal errors which may occur as ground faults. There are different types of protection relays, but most common are overcurrent-, distance-, residual current- and differential protection.The purpose of this thesis was to deepen our knowledge of relay protection and to use the theoretical knowledge we got from the university studies in the work process. In the process we discovered which parameters were the most essential and calculated these for all relay protections on the substation. We also carry out a comparison between two brands of relay protection, ABB and Alstom.During our work we will test and simulate the over-current relays in a program called NEPLAN, the program will also calculate the fault currents.

The problem presented in this report is that of finding a method to calculate the lift force from a single-element airfoil of arbitrary shape. A number of restrictions are used in order to simplify Calculations while retaining reasonable accuracy. The problem is solved for the two-dimensional case only and no finite-wing effects are taken into account. Furthermore, inviscid and incompressible flow is assumed. The method used to solve the problem is the vortex panel method, with vortex singularities distributed over simplified airfoil geometry.

Dione kullager AB is a company in Uppsala, which sell industrialmachinecomponents, transmissionsolutions and provides repair serviceof hydraulic components.When a hydraulic cylinder is about tobe repaired it needs to bedisassembled. Because hydrauliccylinders usually work in dirtyenvironments and are heavilyworn some types of cylinders arealmost impossible to disassemble.Today the disassemble is made by hand,which means extra work for themechanics. In order to facilitate thedismantling of this type of cylindersa machine is to be developed for thispurpose and this is where this thesisbegins.The thesis has been organized in threephases: Literature study in whichfacts and theories are acquired.Concept generation in which differentconcepts, Calculations, and solutionswere identified and selected. Thedesign phase where all the differentconcepts of components were assembledand simulated in SolidWorks. Similarstructures have also been studied inorder to identify necessary functions.The thesis resulted in a structurewhich is believed to meet therequirements.

This thesis has been written at Linköping University for the company Instrument Control Sweden AB (ICS).ICS is a small company located in Linköping that develops software and hardware for Unmanned Aerial Vehicles, UAV. At present, ICS has a fully functional autopilot called EasyPilot but they want to reduce the autopilot?s size to make it more attractive.The purpose of this thesis was to investigate if it was possible to reduce the size of the autopilot and how, in that case, it would be done. It was also necessary to examine whether the old processors should be replaced by new ones and how hard it would be to convert the old software to these new processors.To succeed with the goals many of the old components had to be changed for new, smaller ones. Some less necessary parts were also completely removed.

The Healthcheck is an evaluation of the 2003 years reform of the Common Agricultural Policy (CAP). When the Healthcheck of CAP is decided, most likely in the beginning of 2009, there will be a discussion about how CAP will appear in the next budget period 2013. One main question in the Healthcheck is how the farm support will be designed. A suggestion that has arised is if todays addition amount for dairy- and beef production should be transferred to the fundamental farm support. In this exam theses Calculations has been done in created typical farms in every Swedish support region for cereals-, dairy- and beef production.

This report discusses the constructionof different types of exterior wallconstructions and analyses wall layers.Standard wall constructions from theSwedish building contractors NCC andSkanska and also from the materialproducer Isover have been chosen for theresearch. Life cycle cost analysis hasbeen made to conclude the mostprofitable wall type, seen from asustainable and economic perspective.The Calculations have been made for aperiod of 50 years.The report shows that building with wellinsulated walls is a more profitablesolution both economically and whatconcerns sustainability even though thehigher investment. However, when wallssimilar insulation properties are beingcompared, the study proves that lowerinvestment cost is more profitable.The report introduces requiredconstruction techniques of walls inorder that the reader should understandwall constructions with different layersand properties. The essay shows theimportance of properly constructed wallsto avoid air leakage and moisturedamage.The essay has been implemented byliterature studies, contacts with NCCand Skanska and by energy Calculationsmade by hand and using the software VIPEnergy..