The energy sector is facing an impending paradigm shift. Today?s technology enables the end-user to generate their own energy locally at home. Furthermore, recently developed storage technologies make it possible to balance energy demand with stored energy and integrate district heating with the local power grid. This means that in the future heat and electric power will interact and energy flows is converted over energy boundaries.

ABSTRACT: Commercial swab transport systems are used for collection and transporting of fecal and other microbiological samples. This system must maintain viability and contribute to survival of microorganisms during transport to the laboratory. Four swab transport systems have been compared, eSwab, ?- Transwab and fecalSwab, all three with flocked swabs, and Copan Venturi Transystem with rayon swabs. The study followed the recommendations from the Clinical Laboratory Standard Institute; document M40-A for recovery of Samonella, Shigella, Yersinia and Neisseria gonorrhoeae after storage for 0, 6, 24, 48 and 72 h at room- (22-25°C) and refrigerated (2-8ºC) temperature.

Uppsats för avläggande av filosofie kandidatexamen i Kulturvård, Trädgårdens hantverk och design, 22, 5 hp, 2015.

Grassland is a great part of Swedish agriculture and there is a demand of what the grassland yield is in practice. To be able to control the economic of the milkproduction it is important for the farmer to know how big quantities of pasture there is to use during the year.The work is based on interviews of 22 farmers from southern part of Sweden. Their area of grassland fluctuate between 16 up to 360 hectares. The questionnaire content 32 questions.The most common way to weight the green plant material is to drive over a scale, and to measure the dry extract with your own gauge. It takes in average two minutes toweight one load of green plant material.

This report has a dual focus. The first goal was to increase the knowledge of how the use of electricity in a residential building is distributed. Electricity in residential buildings is used for lighting in common areas, elevators, pumps and many other appliances. The electricity used for these different parts is to a great extent unknown. A few studies have been carried out and the result of these is referred to in this report.By means of measurements and approximations the use of electricity for various appliances became known.

This report has a dual focus. The first goal was to increase the knowledge of how the use of electricity in a residential building is distributed. Electricity in residential buildings is used for lighting in common areas, elevators, pumps and many other appliances. The electricity used for these different parts is to a great extent unknown. A few studies have been carried out and the result of these is referred to in this report.By means of measurements and approximations the use of electricity for various appliances became known.

The main purpose of this thesis has been to address the problem connected with conservation ofspecific objects in historic buildings that have a protected building status. The immaterial demandsand environmental concerns of a place of cultural significance are discussed as opposed to the welladaptedsetting of a museum, with regard to long-term preservation. In an authentic interior of acertain era, large-scale individual treatments of the objects that define it and regulations forconservation-related reasons, may not be considered a worth-while effort, as it is often the integrityof the environment as a whole that has been declared as significant. To investigate the relationshipbetween object and its context, a case study has been conducted by examination of the propertycalled ?Curmans villor?, located in the seaside community called Lysekil.

A lot of houses built during the Million Homes Programme are in need of major renovation. Today?s technology and materials are better than in the 60?s and 70?s. Both Swedish government and the European Union have set climate goals regarding energy consumption by 2020 and 2050. Achieving these goals would require better standards in buildings than the Building regulations demands, such as Umeå municipality?s construction requirements for new buildings.The report aims to investigate if a renovation of apartment buildings from the Million Homes Programme can reach Umeå municipality?s construction requirements.

Chapter 1 defines the aim of the project and gives a general orientation about ground heat extractors. In chapter 2 physical processes that could be expected to be involved in the heat transport around a ground heat exchanger are discussed. It is shown from a literature study what amount of moisture transport due to thermal gradients there could be expected in a ground heat exchanger. The conclusion is drawn that the moisture gradient (Sr) is of same magnitude as the driving temperature gradient (°C). At the expected amount of increased moisture around the pipes the moisture transport could be considered to have a little effect on the brine temperature.

I?ve tried to find the most effective and cost effective way to harvest straw for energy recovery.You can choose between round bales and big square bales. Square bales are the cheapest way to produce straw for fuel recovery because you can optimize the length of the bales so they fit the transportation equipment.In the Malmö area the average days of harvesting hay is 55. The effectively of transportation depends mostly of the speed, the distance and density of the bales. To increase the capacity of bale transportation larger loads and higher density of the bales is necessary.

ABSTRACT: Commercial swab transport systems are used for collection and transporting of fecal and other microbiological samples. This system must maintain viability and contribute to survival of microorganisms during transport to the laboratory. Four swab transport systems have been compared, eSwab, ?- Transwab and fecalSwab, all three with flocked swabs, and Copan Venturi Transystem with rayon swabs. The study followed the recommendations from the Clinical Laboratory Standard Institute; document M40-A for recovery of Samonella, Shigella, Yersinia and Neisseria gonorrhoeae after storage for 0, 6, 24, 48 and 72 h at room- (22-25°C) and refrigerated (2-8ºC) temperature.

This report has a dual focus. The first goal was to increase the knowledge of how the use of electricity in a residential building is distributed. Electricity in residential buildings is used for lighting in common areas, elevators, pumps and many other appliances. The electricity used for these different parts is to a great extent unknown. A few studies have been carried out and the result of these is referred to in this report.By means of measurements and approximations the use of electricity for various appliances became known.

This report is the result of a thesis conducted at the consulting firm Bjerking AB andis the final part of the Bachelor Programme in Construction Engineering at Universityof Uppsala. The work aims to investigate the costs and how the choice of ventilationsystem affects building projects during a long-term period. This report covers costssuch as investment, maintenance and energy but also how they affect residents andbuilders. Building regulations for energy consumption are expected to be tougher;therefore a comparison of two different heat recovery ventilation systems(HRV-system) was made. One system is based on a centrally placed unit that coversthe whole buildings ventilation through vertical shafts.

This report has a dual focus. The first goal was to increase the knowledge of how the use of electricity in a residential building is distributed. Electricity in residential buildings is used for lighting in common areas, elevators, pumps and many other appliances. The electricity used for these different parts is to a great extent unknown. A few studies have been carried out and the result of these is referred to in this report.By means of measurements and approximations the use of electricity for various appliances became known.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..