This thesis describes a conceptual design of a support frame for a synchronousgenerator used in a vertical axis wind power plant. In this system the generator isplaced on ground level. The thesis also considers the design of housing for thesupport frame and generator. The concept presented in this report is based on anearlier design. Besides geometric design, simplified simulations has been run in orderto optimize some of the parts included in the construction considering naturalfrequencies and structural strength.The result is presented as CAD-models andan assembly drawing..

This thesis investigates the underlying factors behind sexual risk-taking and non-risk-taking behavior with regard to Sexual Reproductive Health (SRH) among adolescents in Lusaka, Zambia. The Qualitative Approach was used for data collection and analysis and using the theory of Social Construction, the author explains how different contexts and aspects in the Zambian Society, that is Traditional, Socio-economic, Political, etc., influence the sexuality or sexual behavior of young people in Zambia. Hermeneutics was used to interpret the meanings in the texts/transcripts acquired through data collection and from the author?s knowledge and understanding of the Zambian historical and cultural contexts within which the participants of the research were constructed. Max Weber?s Ideal Type concept was also used to explain that each young individual?s sexual behavior is uniquely constructed by societal aspects.

Lansen Technology is a security company from Halmstad, Sweden and their focus indeveloping and selling alarm solutions. One of their latest inventions is a vibration sensor thatrecognizes very small movements in the ground.The thesis work was made in cooperation with Lansen Technology AB and the task was toinvent a test equipment that decides whether the sensor is working correctly. By generatingcertain frequencies with specific amplitude, we will expect the sensor to give a similar output.The final report includes all the parts of our work as studying, choosing components,programming, construction, results and conclusion..

Följande rapport bygger på examensarbetet inom CAD-teknikerprogrammet påHögskolan i Halmstad. Arbetet innefattar framtagning av ett höjdjusterbartarmstöd till bilförare, en produkt som inte finns på marknaden idag.Utförandet av arbetet har bl.a. inneburit kriterieuppställning med krav ochönskemål, framtagning av produktförslag i form utav skisser och 3D-modeller, valav material genom undersökningar, även protoyptillverkning och produktanalyser.En del vikt har lagts på att genomföra marknadsundersökningar för att se om detfinns ett intresse för produkten..

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This thesis work is about how technical consulting companies can accept their organization before a coming recession. Technical consulting companies are together with the rest of the actors in the construction business constantly depended on the current economic situation on the market. How to adapt the organisation depends on the current situation on the market.To adapt the organization in the best way possible the companies need to recruit and educate personal. It is then very important to find a solution on how the current change of generation in the companies will be handled. The large and very much competent group of 40-talists will in a few years retire.

This thesis treats Building Information Modeling, BIM, in the production stage. Brieflydescribed BIM is virtual model of a building object where all information about theobject is gathered. All the involved operators in the construction project have access tothe model and can gather or share information about the project. There are several waysto apply BIM in the production stage. This thesis primarily deals with visualization of theobject, preparation and planning, the ability to take amounts from the model andcoordination and clash control.The basic issue was highlighted by Byggdialog AB.

Cement manufacture accounts for 3-5 percent of total global carbon emissions. There is a growing interest in reducing the environmental impact and conserve limited natural resources. In cement production, clinker productions consume 87.5 percent of the total energy consumed in the cement manufacture.Cementa has since many years, focused on reducing the environmental impact of cement production. The work has involved the entire production process from selection of alternative fuels to the development of cement with less clinker content. During 2013/2014, two new types of cement (Bascement and CEM II / B) will be introduced to the Swedish market.

There are around 855 000 on-site sewage systems in Sweden and some 1 800 of these are located in the municipality of Sigtuna. The Sigtuna local authority has set the goal that all sewage systems with insufficient function should be improved before the end of year 2010. A malfunctioning on-site sewage system may cause three main problems: spreading of diseases, discharge of eutrophicating compounds and wastage of resources. The municipality strives to reduce these problems already at the stage of granting permits for installation of on site sanitation systems. The municipality has recently adopted new guidelines, which demands certain minimum reductions for different compounds. The guidelines also state that it is preferred that neighboring house-owners cooperate in jointly built and operated sewage systems and that the system should be able to recycle plant nutrients.

The Mission at ÅF Industry in Norrkoping was about optimizing bulk data handling while importing process tag types from their construction database into the Process Controlled System of type Siemens PCS7.I found three different methods to solve the task. Two of them were using different software from Siemens under the premise that the report from the database was corrected as needed. The third variant was manually creating the circuits. All methods worked out fine but there were times when one was better than another.To solve this task I had access to all software presented in chapter 2 ?Programvara? (=Software).

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

The collection of hazardous waste from the household around Swedish municipalities varies. 1% of the households waste is hazardous waste. It has hazardous features that can give bad consequences for the nature and human health if we don?t collect it and treat it. Therefore the law controls it, the municipalities have responsibility for the household waste.

This paper is an account of the work around the arrangement and registration of the archive of the Swedish Art-ists? Association?s archive. The Swedish Artists? Association is an association of artists that both makes exhibi-tions for their members? works and handles the Artists? House, called Konstnärshuset in Swedish. During the work with the archive the author faced a number of challenges and problems.