This thesis investigates the socio- and environmental economic effects of a deep repository for spent nuclear fuel in Forsmark in the municipality of Östhammar. I seek to show the general picture but focus on the effects on employment, environment and income. Cost-benefit analysis is used to investigate the differences in utility between a scenario with and a scenario without a deep repository in Forsmark. Most of the possible effects can not be valued and many can not even be quantified with the data available today. Therefore this thesis has a bit of a ?preliminary study character? and seeks to show what we know today and what needs to be further investigated when available data allow it. The costs that could be valued are noise from the traffic during the period of building and emissions of carbon dioxide and nitrogen oxides from the transportation of rock masses during the building period.

This thesis is made by Carl Persson and Alejandro Saavedra for Gryaab. Gryaab is Gothenburg?s water processing plant and produces about 60 GWh biogas annually with a flow around 1150 Nm3/h. Gryaab wants to research their possibilities to become independent with electrical energy and the possibilities to enrich, upgrade biogas. The use of methane rich gases like biogas and natural gas is today low in Sweden compared to major parts of the world.

In the last few years people have become more and more aware of how humanity is affecting the climate. In the direction of reducing the greenhouse gases is to design engines with higher tensile properties and reduced weight, in order to achieve lower fuel consumption and cleaner fuel incineration in today's truck engines.In order to achieve these requirements it?s necessary to increase the combustion pressure in the engine. This requires higher tensile properties and high thermal conductivity of the engine material. The department of Component Technology at the University of Jönköping in collaboration with Volvo Powertrain AB, Scania CV AB and DAROS Piston Rings AB has been commissioned to develop this material and to find knowledge of material properties used in truck engines and piston rings used for marine applications.The purpose with this work is to analyze the tensile properties of a series of cast iron, cast under different metallurgical conditions.Four different series of cast irons have been analyzed from four points of view, carbon concentration, nodularity, amount inoculation and cooling rate.After the tensile test all specimen data was analyzed in a mathematic calculation program called Matlab 2006a.

Diesel electric propulsion is in many ways a good alternative to conventional shaft propulsion, both economically and environmentally. There are also many other good side effects which need to be considered, i.e. better manoeuvrability, more efficient use of space and less noise on board. However, there are applications where diesel electric propulsion is not profitable. Large ocean going ships? profitability is much depending on fuel costs and the diesel electric alternative cannot compete on long journeys with large low speed engines.This thesis will treat the aspects of choosing between a diesel electric system and a classic mechanical propulsion system.

Until 2020, 49% of Sweden's use of energy must derive from renewable sources. Greenhouse gases must as well decline with 40% compared to 1990 as a part of Sweden's 16 environmental objectives. Biogas is part of the effort to achieve these objectives, but as the demand for biogas increases, more substrates are needed to meet the demand. The purpose is to investigate the conditions for pea residue as substrate by performing lab-scale mesophilic digestion with different fractions and notch lengths and then to summarize pea residue as a substrate for biogas production. During anaerobic digestion, 1000 ml bottles were used as reactors for digestion.

The Swedish road transport sector relies almost completely on fossil fuels. In 2007, as much as 96 percent of the total sales of fuels was made up of petrol and diesel, while at the same time the share of total emissions of greenhouse gases in Sweden that came from road transports amounted to close to 30 per cent. Sweden is by no means worse off than any other European country in these respects. In order to address the questions of high oil dependence and CO2 emissions the European Commission has proposed a reinforcement of the legislative framework, with a 10 percent minimum for the market share of biofuels in 2020. Furthermore, the proposed target is binding for the member states, unlike the current voluntary target of 5.75 percent by 2010. More than doubling the usage of biofuels in only a bit more than a decade will most likely not be possible without policy interventions.

Fuel wood is currently the third largest assortment from the forest in Sweden after pulpwood and lumber. Branches and tops i.e. logging residues are one of the assortments of fuel wood which is a common by-product after harvesting nowadays. The way to utilize, disintegrate and transport the logging residues varies between northern and southern Sweden. Branches and tops are collected throughout the year at appropriate stands, but are consumed mainly wintertime.

This master thesis encompasses an inventory of the older industrial community of Gimo. Investigations of the contamination situation for each industrial area were done. A risk classification according to the Swedish Environmental Protection Agency?s ?Method of Surveying Contaminated Sites?, phase one, followed. The risk classification was done on areas of Iron Work, a rockwool industry and a landfill. Gimo have had iron manufacturing from 1615 until 1945. Gimo have had two blast-furnaces and two smithies periodically.

As trucks are getting more and more advanced, information about their weight has become a key factor for controlling them in a more fuel efficient and safe manner. Knowing the mass of a heavy duty vehicle in real time has been a difficult challenge for the truck manufacturers. With the processing power for electronic control units in trucks steadily increasing, more advanced algorithms for calculating the mass has been developed, but at the moment there still is a wish for better performance.Since there is a lack of good information regarding the external forces acting on the vehicle, forces that depends on the slope of the road, foundation of the road and the wind, the methods have to be able to disregard these. Such an approach, based on an indirect least square solution, has been evaluated in this thesis. The results have been promising and based on these a recommendation about further evaluation has been made..

Namibia, southern Africa, suffers from an energy shortage and is therefore facing severalchallenging problems. The use of firewood as fuel for cooking is common in the whole countryand has negative consequences for health and the environment. This work have focused ondeveloping a solar baking oven, calledSunbaker, adapted for Namibian families needs forbaking. The development was based on classic solar cooking limitations, specific needs forNamibia and to have a feasible manufacturability.The project started with a theoretical study in Sweden where different solar cookers, informationregarding Namibia, technical aspects and end user aspects were studied. To assess the need for asolar baking oven aMinor Field Study took place in Namibia during eight weeks in July toSeptember 2009 and resulted in a product design specification.

Sammanfattning Ensilerat vallfoder är ett av de absolut viktigaste fodermedlen för att förmå korna att producera en stor mängd högkvalitativ mjölk. En hake är dock att ensilaget ska vara av god kvalitet och med bästa möjliga näringsvärde, samtidigt som man även vill ha volymmängder. För att få detta gäller det att skörda vid rätt tidpunkt, vilket kan vara svårt att veta när det infaller. Till detta finns ett hjälpmedel som kallas skördetidsprognos. Detta går ut på att man klipper prover i vallen upp till tre gånger innan första skörden för att analysera gräset och därigenom kunna avgöra när bästa tiden är för att skörda för att få den mest optimala kombinationen av mängd och näringsvärde. Syftet med detta arbete är att undersöka hur bra hjälpmedel jordbrukare i norra Sverige tycker att skördetidsprognosen är för att få en ökad kvalitet på ensilaget, samt att jämföra variationen i näringsvärde och mängd biomassa inom och mellan olika fält.

With a changing climate, we can expect higher temperatures and more precipitation in Sweden.As the temperature increases, new weed species are expected to migrate in from more southerlylatitudes, resulting in requests for new techniques for weed control. In addition, we might see agreater number of weed species and higher biomass production due to increased concentrationof CO2 in the atmosphere.Increased understanding of the biology of specific weed species will become more importantin future weed control. This will help to control the weeds more efficiently. Higher prices onpesticides and a public demand for reduced use of pesticides make growers more inclined to usemechanical weed control on a larger scale and to a greater extent prevent weed establishmentbefore sowing. A well-planned crop rotation is the most important preventive measure, whichmight also include delayed sowing, and dark harrowing and sowing.Research takes place on many levels within the weed area and several alternative methodsare being developed.

Using the Introductory Carbon Balance Model, ICBM, five different crop rotations with rye 1. Rye-Ley-Ley-Rye-Beans-Rye 2. Rye-Rye-Rapeseed-Rapeseed 3. Rye-Ley-Ley-Rye-Potatoes-Rye 4. Rye-Rye-Potatoes-Wheat 5. Rye-Rye-Potatoes-Beans-Wheat-Rye-Potatoes-Rapeseed were tested theoretically in four different cultivation scenarios ? Straw left on the field, biogas digestate added as fertilizer. Labelled ?+straw+BD?. ? Straw left on the field, only synthetic fertilizer. Labelled ?+straw-BD?. ? Straw harvested, biogas digestate added as fertilizer.

The knowledge of the chloride content and its fluxes and patterns in trees is insufficient. Increased knowledge would be desirable, one of many reasons is to be able to more efficiently meet the problems that the substance causes in the pulp industry. The purpose of this study was to examine and describe the chloride concentration of Norwegian spruce (Picea abies L. Karst.) in the south of Sweden. Furthermore the aim was to be able to predict chloride concentration from readily measurable site factors.

The thesis describes a completely new biofuel system to generate particle-free heat from combustion of ash-containing biofuel particles at high temperatures.The suggested system gives opportunities to introduce biofuels in new areas.Main components in the suggested system is a heat radiating combustion chamber intended for pulverized wood, combined with regenerators to extract heat from flue gases and simultaneously preheating the combustion air.The thesis contains a description of the suggested system, theoretical considerations, calculations regarding the combustion, and includes results from tests performed.The results from calculations and tests performed concludes that the system is workable and possible to apply..