Ever since ABB has begun diecasting their rotors instead of permanent mold casting it,variation in the quality of the cast has arisen. Diecasting is performed in three differentmachines, M1, M2, M3 with 400, 660 respectively 800 tons of die locking pressures.The aim of this thesis is to answer the following questions:What is the ?right? cast quality? How is the right quality achieved?For sizes 160-180 solutions will be proposed that consider eccentricity between thelaminate and the short circuit ring as well as elimination of the thin Al film that appearson the outer periphery of the rotors.Through considering the statistic material the most often diverging rotor type has beenidentified and one of the actual rotors has been sent to a laboratory to be analyzed inorder to establish the current defects. The result of the analysis shows that there areplenty of gas- and oxide-porosity.It has been proved that every time the dies temperature decreased below 120°C thecontent of gas porosity increased. It is due to rapid solidification of metal that flowsthrough the ?cold? laminate.It has confirmed that enhanced porosity in squirrel cage causes high impedance in therotors.

Den här uppsatsen är baserad på en enkätundersökning samt intervjuer med gymnasielever angående deras tankar kring djurförsök. Jag har intervjuat studenter från två olika naturbruksgymnasier. Båda har inriktningen djurvård men det är endast en av dem som ger en specialiseringskurs inom forskningsdjur.Min frågeställning är att undersöka om elever som läser kursen i försöksdjurskunskap har en annan inställning än de elever som endast läser djursjukvård. Som resultaten visar så är de eleverna som läser specialiseringskursen mer positiva till både djurförsök och att jobba med försöksdjur. De har också en mer korrekt bild och större vetskap om hur verkligheten ser ut för försöksdjuren.

If you have access to wood, a wood burning boiler is a cheap way to heat your home, but it is certainly not the most convenient option. Wood requires many operations and management, which takes time. One way to reduce this workload is to have a modern boiler with automatic ignition. Enertech/CTC has a desire to create an accessory with automatic ignition to a modern wood burning boiler. Today there is no boiler on the market that can ignite firewood automatically without the introduction of paper and sticks.

The goal with this master thesis has been to evaluate and to examine the stationary resistance bridge. The resistance bridge uses a 4-point measuring to determinate the resistance, which is used in the manufacturing of the conductor. It is then used when the resistance is to be decided for coarser aluminium conductors. A conductor has to fulfil certain demands to be able to move forward in the process. One of these demands is the resistance in ohm/km, which has demands that the measure values of the resistance bridge are as true and precise as possible. The stationary resistance bridge had been examined through various kinds of measurements to be able to see how stable the system is and how to obtain a measure value as optimized as possible.

The last few decades the development in the field of electronics has been huge. The components performance gets better at the same time as the manufacturing cost decreases. Many of the design moments that have to be done, are done automatically today, but it can get better. Especially for analog circuit design.At Electronic System in Linköpings universitet, research is in progress to develop a tool that can design analog circuits in reasonable time. It means that it has to size the components (transistors, resistances, capacitances etc), so that the circuit can fulfill the performance requirements.

This thesis studies whether private equity owned firms within the Swedish welfare sector distinguish themselves in terms of tax planning and short-termism from a control group consisting of other privately owned welfare firms. For the first time, the comparison is made on the entire welfare sector, between 14 matched pairs within education, health care and elderly care. We use financial metrics associated with tax planning and short-termism in sign tests to examine whether the private equity owned firms differ from our control group. The financial metrics tested are actual and paid tax rates, level of interest, book-tax gap, investments, personnel expenses per employee, and cash earnings. We find that the private equity owned firms in terms of tax planning only differ in the level of interest, while no notable differences are found in terms of short-termism..

This report describes the development process of a pipe clamp used on exhaust system for cars. It is made based on the manufacturers desire to improve and make the clamp easier to manufacture and to reduce its price to their customers. This should be done either by manufacturing the clamp in one piece without an expensive and work intensive welding process, or by generating ideas of how to develop a brand new type of clamp. Investigating the market for similar products was done to eliminate intrusion of other manufacturers? patents but also to generate ideas.

This report is written for a consultant networking company with the purpose to review the development ofthe company's remote connections from a user friendly and security perspective.This includes an investigation of the possibilities to consolidate existing authentication methods foraccessing customers. The problem lies in the amount of methods being used. Through case study wefound that smart cards, SMS-service, software and hardware tokens exist.The only method feasible from a security perspective is smart cards. Since the method is not commonlyused by the company's customers a standardization of it would be counterproductive.Also, the purpose of this report is to investigate how the ongoing internal development of the remoteconnection will affect the company's clients. Within this framework we have also verified a designsuggestion.We interpret, after the completion of the case study, that the internal development of the remoteconnection is marginally affected by legal perspectives.

The aim of this study is to examine the patient's understanding of the counselling while testing for an STI. The method was an inquiry directed to patients at two receptions, where tests for STI are made, and on the Internet for patients who made a test within the last year. The study involves 95 participants, 39 answered the inquiry directly after the test. The main results show that most participants are positive to talk about their sexuality and sexual strategies with the personnel, irrespective of who takes the initiative to the counselling. Women are yet more negative then men to talk about their sexuality, even if the test is made voluntarily by the woman.

Context. Performance and resource usage is often an important factor for database driven services. Depending on the purpose of the application, choosing the wrong type of database may require unnecessary hardware upgrades or replacements. Objectives. This study investigates the differences in performance and resource usage between different SQL- and NoSQL-databases.

Blood-borne infectious diseases such as Human Immunodeficiency Virus (HIV)and Hepatitis C Virus (HCV) spread when the addicts share needles and injecting equipmentwithin contact networks. A quantitative cross-sectional study was conducted in Winnipeg,Canada in December 2003 - September 2004. Through a special questionnaire, respondentswere asked to answer questions about themselves and about their contacts, about relationshipsand how they shared syringes and other injection supplies. Blood tests were used to identifywhether they carried any blood-borne infectious diseases. We selected some variables from theoriginal data set.

This master thesis is made of two parts. The first part concerns the method and results ofdesigning a motion control system for a piece of research-equipment called BIRGIT. Theequipment is made to be used for research on eyemovements. In the second part, a computermodel of a part of the balance organ in the inner-ear is developed. The work has been done atthe Bernadotte laboratory at S:t Erik Eye Hospital.The equipment the control system is made for is a so-called rotationchair.

The spatial population structure of the saprotrophic basidiomycete Tulostoma brumale was investigated at a site in south eastern Sweden. Sporocarps were mapped and collected, and somatic incompatibility tests between mycelial cultures cultivated from the sporocarps were used to identify genets. Calculations of the size and numbers of genets and their distribution were performed. The spatial distribution of the tested sporocarps and the identified genets are presented graphically in a grid. The total number of identified genets within the investigated area (1210 m2) was 27 based on 48 tested sporocarps.

Background: Low Price-Earnings ratio, low Book-to market ratio and low stock prices can give the impression that a stock is ?cheap?. Is it through systematic use of these portfolio strategies possible to beat the market index ? in other words does financial illusions exist? Purpose: To examine if the Stockholm Stock Exchange is an efficient market. Limitations: The efficiency is tested solely through the chosen portfolio strategies: low Price-Earnings ratio, low Book-to-market ratio and low stock prices.

This is a technical report about cement stabilization in general and the stabilizationprocess during the construction of a warehouse in Halmstad, Sweden in particular and iswritten at the section for economy and technology at Halmstad University incollaboration with NCC Anläggning.NCC encountered variations in compression strength in the stabilized material on the firstwarehouse that they constructed for the company Biltema. In our report we used thestabilization process of the second warehouse for the same company as a reference todetermine what could be done to get a more homogeneous result for future projects.We also looked in to what testing method is the most suitable to determine the result ofthe stabilization.After interviews with people involved in the process and visits on the work site we havecome to the conclusion that the most probable cause to the variations in compressionstrength is segregation in the ballast material. This segregation can occur in severaldifferent occasions in the process such as during the production, transportation andhandling on the work site.Other causes for the variation can be improper compaction, overlapping stabilization insome places and different duration of hardening of the samples that are tested.The best way to do in situ test of the stabilized material is to do seismic investigations asthose are non-destructive tests in comparison to taking core samples and you can discoverany cracks or air bubbles in the material..