According to a decision of the European Commission, measures are to be taken to reduce the use of energy in the EU. The goal is to reduce it by 20 % compared to the current use. This shall be done to the year 2020 (European Commission, 2011). One industry that use large amounts of energy is the construction of buildings which account for almost a third of the energy use (Brogren, 2012). The major part of the energy that is used in the construction industry is not used when the buildings are built, but rather during the rest of their subsequent lifetime.

The purpose of this essay is to examine if the judgments of accountants differ, in different cases, between the old and the new law. The method we used to investigate the differences was a combination of experimental and non experimental. Our analysis is based on a survey investigation with ten cases. These cases are produced from a model in which the accountant tests his independence. The survey was sent by mail to about a hundred accountants.

SAAB Automobile ABis a car manufacturer within General Motors corporate group. SAABAutomobile ABhas a big part of the responsibility for the brake development in the corporategroup. The car industry is facing harder environmental requirements, which influence the brakedevelopment. The focus is to develop brakes with low drag and sustained brake feeling andperformance. Important characters for the brake caliper are high stiffness and low weight, highstiffness results in high performance and low weight is important because it is unsprung mass.This thesis investigates the possibility to improve the performance of the brake caliper for aGMproject.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

The issue about how Scania shall perform HVAC tests in the climatic wind tunnel CD7, which Scania is about to complete by year 2013, has resulted in four test methods for truck HVAC and also a test method structure. The test methods have been chosen to focus on sun, snow and rain simulations. These are adapted and developed according to what should be tested and to what can be tested in CD7, which has been the object. With CD7 different climates can be simulated in a controlled environment for complete truck level, from desert with high sun load to arctic cold and snow.The test methods represents a basis to start from, for designers and test engineers which make the testing more repetitive as well as time eventually can be saved. Before the test methods can be applied they must be verified as they are based on theoretical and empirical assumptions.

Denna fallstudie har utförts vid Sandvik Mining and Construction Köping AB, ett bolag tillhörande Sandvikkoncernen, som tillverkar borrkronor till gruvindustrin. Organisationen arbetar med förbättringsarbete enligt principer från Lean production, vilket bland annat innebär att en större layoutförändring pågår i fabriken med syfte att förbättra det övergripande flödet. I samband med detta förbättringsarbete kommer den manuella monteringslinan av borrkronor att flyttas. Detta ger möjlighet att se över monteringslayouten utifrån värderingar, principer och verktyg från Lean och ergonomi. Syftet med studien är att lämna förslag på en monteringslayout som är utformad på ett sådant sätt att den minimerar förekomsten av icke värdeskapande aktiviteter, förebygger fel samt skapar goda förutsättningar för en ergonomiskt lämplig arbetsmiljö.

The first browser war took place during the second half the 1990s, and Internet Explorer cameout as the winner over Netscape Navigator. Today a new browser war is being fought withmany competitors and the future is uncertain. The purpose of the thesis is to find out how theweb browser market has developed since the start of the previous conflict, and we ask ourselveshow it will continue to develop in the future. This is accomplished with, among otherthings, interviews, tests and already existing statistics. The thesis' conclusions shows that theweb browser market has developed in a positive way from several perspectives, both for theusers as well as for the web developers.

 Akademin för utbildning, kulturoch kommunikation                                                                            EXAMENSARBETE                                                                                                                  UÄÖ007 15 hp                                                                                                                  Vårtermin 2010SAMMANDRAG                                                                                   ­­Bild här) kationldning, kulturch ko__________________________________________________________Ann-Charlotte Fernkvist Lärares arbete med skrivuppgiften i det nationella provet i svenska i årskurs treTeachers? work with Swedish writing assignments in the national tests given during the 3rd grade År 2010                                                             Antal sidor: 47_______________________________________________________Syftet med denna studie är att genom intervjuer belysa lärares arbete med skriv­uppgiften i det nationella provet i årskurs tre. Studien avgränsas till hur lärare prak­tiskt förbereder, genomför och bedömer skrivuppgiften. I studien har fyra informanter intervjuats utifrån en kvalitativ intervjumetod.Studien visar bland annat att informanterna har skilda erfarenhet av nationella prov och att de har kommit olika långt med genom­förandet av 2010 års prov. Även om deras erfarenhet skiljer sig åt har de liknande grundtankar inom förberedelse, genomförande och bedömning.

This master thesis comprises analysis and dimensioning of a keyed joint between a generator axis and a hub with aid from the FEM-software ANSYS Workbench 13.0.The generator axis is a part of a hydroelectric power station that generates electricity with a reactions turbine, a Kaplan turbine. The existing keyway consists of one parallel key with the width 90 mm and height 45 mm. Due to a planned increase of the power of the generated power with 32 % a design study was needed to see if the keyed joint would be suitable for the extra force. Because of the fact that the axis diameter is bigger than the standards covers/recommends a the keyway had to be re-dimensioned. In an earlier assignment from Skellefteå Kraft AB to Sweco Energuide the keyway was planned to be properly dimensioned, but no final solution was approved.During this master thesis a number of different numerical tests were made.

The tick-borne disease bovine anaplasmosis is primarily caused by Anaplasma marginale. A variety of wild animals act as reservoirs for A. marginale, but the understanding of their role in the epidemiology of A. marginale is yet poor. This cross-sectional study was conducted to establish if proximity of wildlife affect the prevalence of bovine anaplasmosis in cattle.

This master's theses was carried out on assignment from Stockholm Vatten AB as a part of a project developing new waste water treatment techniques. The goal of the theisis has been to evaluate an anaerobic membrane bioreactor for treatment of waste water from Hammarby Sjöstad. The bioreactor has not been heated and the main interest has been to study the gas production, power consumption and the reduction of organic matter and nutrients.The system has been completed with a reverse osmosis unit and a total of four batch runs have been made with good results. The use of reverse osmosis allows nutrient in the waste water to be reintroduced into circulation as the reverse osmosis concentrate can be used as crop nutrient.The membrane unit is of VSEP ("Vibratory Shear Enhanced Processing") type and an extensive membrane test has been conducted. This so called L-test helped determine the most suitable type of membrane for the system to allow a higher ±ux and thus lower power consumption.

Globally, coastal ecosystems like mangrove forests, sea grass meadows and salt marshes are well known for their ability to capture and store atmospheric carbon effectively. In Sweden, there is still limited knowledge about local coastal ecosystems with similar functions, with alder swamp forests being an interesting example. Therefore, this study aimed to increase knowledge of the factors that can contribute to the potential carbon sequestering ability of alder swamps. Vegetation data and sediment samples were collected from a total of 37 sampling plots across four alder swamps in Bohusl?n on the Swedish west coast.

Mechanical relays are more and more being replaced with semiconductortechnology. In this thesis it is investigated if and how the larger loads couldbe controlled by transistors. The main part of this work aims to create andverify a solution that can control the starter motor, as well as protect it incase of any failure. The different malfunctions that the solution protectsagainst is high current, too high peak current, low current, maximum cranktime and minimum cool off time. The timers also protect indirectly againstoverheating of the starter engine.The transistors used are BTS555, from Infineon.

For many years, the construction industry in Sweden has not developed much of an integral approach for design across disciplines. The sector?s impact on society, economics and environment is huge. To make the interactions within the construction industry more efficient, a relatively new concept called BIM (Building Information Modeling) has been introduced. The idea with BIM is that the different actors of the construction industry will work through intelligent CAD software, with common file formats and more cooperation between different actors during the various steps of the building and construction process.The technical consultancy company WSP Sweden is working actively to implement BIM within the frame of its activities.

During the last year in the Innovation Engineering Program, at Halmstad University, a degree project was performed that was carried out during Fall semester in 2006 and Spring semester 2007. The project was performed by two students in corporation with LIC Audio AB, a company in Stockholm. The degree project was meant to result in a communication aid for people with a cognitive handicap. The project focused on people suffering from dementia because of the expressed need within this group. This aid should first and foremost help in a conversation between a person with dementia and another person, like a relative or nursing home staff.