The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

There are many old dams in Sweden and, since few dams are constructed today, the main task in risk assessment on the existing dams is often to reduce the risk of failure. RIDAS (Swedish Guidelines on Dam Safety) is used when designing new dams and assess the existing ones. The guidelines include stability requirements for different failure modes, e.g. overturning and sliding, which imply that the load effect from e.g. uplift and ice load need to be less than the resisting loads or moments.

Vattenfall Heat AB is a district heat provider in Drefviken, but has yet to establish any cooling systems in this area. This thesis examines the potential client base within the area today and over the coming 20 years. The feasibility of the most common cooling technologies is evaluated and results show a total potential for an installed capacity of 30 MW providing 50 GWh of cooling per year. One of the examined areas shows good prospect for heat driven absorption chillers during the summer months when the heat load is limited..

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis is to examinethe possibilities for adding a floor to anexisting building using the two materialswood and sheet metal profiles as the loadbearing structure. An apartment buildingfrom the 60s has been used as referencehouse. Two different suggestions for thedesign are presented in the rapport. Oneof them has been analyzed with wood andsheet metal as the load bearing structure.Using the old constructional calculationsand blueprints of the existing buildings,the load bearing capacity has beencalculated. In the calculation programFEM-Design the building has been testedwith the loads that an extra floor wouldgive.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis is to evaluate and update load curves for Fortum Distribution AB. Theload curve method is a tool used to forecast the strain of an electric grid. The method is based oncustomer annual energy consumption, outdoors temperature as well as customer category. Theload curve method was established by Svenska Elverksföreningen at the start of the nineties andfocus was put on standardizing annual energyconsumption, in order to make the method usableacross the nation. Present consumption patterns have changed since the original load curves wereproduced, which leads to a need to update the load curves.The work began with an update of present load curves according to recommendation taken fromanother earlier thesis.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

Westhelicopter INC. has an aviation workshop providing qualified helicopter maintenance in accordance with PART-145. Maintenance and administrative base is situated in Luleå at Kallax airport. The types that Westhelicopter INC are currently authorised to service are: Eurocopter AS 350 Base/Line Maintenance, Eurocopter EC 120 Base/Line Maintenance and Robinsson R44 Base/Line Maintenance. The thesis work has been to make new maintenance programme for Westhelicopter INC. This maintenance programme will be used to follow-up the time of the components, service bulletins and ADs.

The governing set of regulations for structural engineering in Sweden used to be Boverket, BKR. However in the beginning of the 21st century a changeover to new regulations, the Eurocodes, started.The transition was completed in year 2011 when the Eurocodes became the mandatory design work policy for all countries within the European Union. The Eurocodes were implemented to simplify and remove potential barriers to trade that may exist when countries have different design rules.  Since the changeover it has been important for all construction companies to update their knowledge base and their design software.When comparing the two calculation processes they seem similar, but there are a couple of differences worth noting.  With the new regulations, engineers will find that the process when designing joints in timber structures has changed.  What used to be a fairly easy and straight forward calculation procedure has now become tedious and time consuming.The objective of this degree project is to present a product, a dimensioning tool that will help structural engineers when computing lateral load carrying joints in timber structures.The degree project is made up of two parts where the first part is the written report describing the background and theory behind load carrying computations. The second part of the project is the actual dimensioning tool which includes several worksheets in Microsoft Excel. The program treats single and double shear connections of the following:Nail jointsScrew jointsSteel plates (thick and thin types) The user can edit the following parameters:Type of plate/ number of shearsStrength class of timber membersMember and plate sizeType of fastenerDiameter of fastenerLength of fastenerYield moment of fastenerkmod and partial factors for design load carrying capacityThe dimensioning tool was created and developed in collaboration with structural engineers at the company Byggteknik AB.

Due to a constantly increasing competitive pressure it is of great importance to constantly strive for improvements in order to gain competitive advantages. Lean Production is a concept that has been introduced with the aim to minimize waste and increase profitability. The purpose of this report is therefore to investigate how to perform effective planning according to the principles of Lean Production, in companys with customer exclusive products, through a case study at Sandvik Mining and Construction (SMC), and to investigate how SMC kan improve their planning of drifting rods at the production unit in Sandviken.The study started by creating a theoretical framework, to describe the subject planning and planning based on Lean Production. This frame work constituted the base for the case study which took place at Sandvik Mining and Construction, and also for the model and planning tool that has been introduced.The result of the study is partly a general model with factors that contribute to a more effective planning. These factors has beed identifed as SMED, which focuses on reducing set up times and in the end to facilitate the planning.

This master of science thesis is focusing on how the fault handling on hardware connected toa control unit on a Scania vehicle is working. To the hardware counts buttons levers, sensorsand CAN. The work has been concentrated upon how the fault handling is working and if it ispossible to find any new fault modes.The control unit that has been studied is called the Coordinator and is the core in Scanias threenetworks of control units. The Coordinators work is to transmit messages between the threenetworks and to process signals from buttons, levers and sensors. The values is then usedinternally or is sent to other control units on the CAN networks.