This report describes the construction and development of a control box, which is a tool for testing and verifying a certain model of Rapid?s built in staplers (model A6102). Basically the function of the control box is to interpret any errors that may occur in the stapler and to make it possible to test fire the stapler.The control box should be able to communicate with the stapler using a specialized communication protocol. The different data such as errors, firmware etc. from the stapler is presented in plain language on a display.

This thesis describes the design of a tipping trailer, from a company?s demands andrequests to complete manufacturing documentation. The design is developed for thecompany Abexor AB in Östersund that produces tipping trailers. The product issupposed to be used by Abexors customer to transport cargos of different kinds,such as gravel, stone, dirt, etc.The work commenced with a meeting at the company where demands were set.After that a pre-study was conducted to find out what traffic rules were required forthe trailer to be allowed to be driven on roads. Similar products were examined tosee how the trailer could be designed.

Background: The Swedish population is aging [1] and malnutrition is a common problem among elderly people [2]. A method called food registration is used to monitor the patients? nutritional intake, with the purpose of reducing the risk of patients deteriorating in nutritional status during hospitalisation. However, the current method is not satisfactory and many food registration lists are incomplete. [3-6] Thus, patients do not receive a qualitative nutritional care since the assessment of the patients? nutritional status is based on incomplete documentation.Purpose: The purpose of this master thesis is to increase the quality in the nutrition monitoring process in the geriatric units B72 and B74 at Karolinska University Hospital in Huddinge, Sweden.

Material handling is a term that includes all kinds of handling of material from a raw product to a finished one. ABB is active in the following segments; foundry, packaging and palletizing, metal industry and plastics industry.The demands for efficiency and reliability have been set very high in the industrial sector. Optimizing of the material handling will give the company higher cost-effectiveness. Around the robot there are different kinds of material flows, to optimize the cycle time, consisting of carriages combined in different ways.Motion Control is a complex system with main functions such as; positioning, synchronizing, indexing and more. The products in the system need to cooperate to make these functions possible therefore integration of motor- and servo products are important.

Today?s electrical grid companies understand that better knowledge of and information about their grid can help realize a smart grid network. One way to gain better knowledge and information about the low voltage network is to install measuring equipment on the substation transformer´s secondary low voltage side that measures the low voltage network losses for that specific substation. By doing so, grid companies can, due to the calculation of the low voltage network losses, identify and address issues such as illegal power dissipation, unmeasured power outtakes, and unsatisfied technical documentation for the substations low voltage network.During 2012, Mälarenergi Elnät AB had a total electrical network loss (both medium and low voltage network losses included) of three to four percent of their total distributed electrical volume. Converting this energy volume into a monetary figure this accounts for a loss of around 30 million Swedish crowns.

The aim of this study is to through six interviews, with six experienced, social workers?, in three cities, understand how the child?s position in the Swedish child protective services? enquiries has change, and the factors behind it. The aim is also to compare if the social workers? view of the child?s position in the enquire has change accordingly to Socialstyrelsens intentions of BBIC. The theoretical approaches that was used is the new institutionalism, the Shier?s pathways to participation and the term discretion.

Visual Type Instrument - VTI, is a tool containing a typeface and a set of geometric calculations that generates numerical data in spreadsheets. The data is determined from the typefaces visual dimensions and is used to calculate leading, type size, margins and format. The aim is to offer, for all of those working with typography and design, a practical way to manage text, image and format in relationship to visual size. Instead of using point measurements, VTI uses a new device called Edo. An Edo is the same as one twelfth of a millimetre.

AbstractResource efficient manufacturing is a term that has been increasingly applied within manufacturing, where one of the key points is to reduce waste of such forms that do not add value for the end customer. By the Lean principles, there are seven plus one types of waste, in which the definition of the eighth point varies among sources. In this study, the eighth type of waste has been interpreted as the untapped creativity and competence among employees that has not been put to use. From this, our question was incubated; How can you make the most of the employees? untapped creativity and potential within manufacturing? The case study will be developed with empirical data obtained from Dometic Group by conducting interviews.From the gathered literature, it was concluded that the communication between employees contributed to an increased understanding of one another as well as it allowed for improvement in work.

Background: Do our elder starve? A good nutrition state gives a good health and comfort. The research displays that is it exists shortages in energy and nutrition needs for the older. Aim: The aim with this study was to elucidate the mealorder and the mealsituation for the elder and how the nurse handles this. Method: This litterateur review was based on teri research studies.

The thesis hears content-error in relation to agreements closed by electronic means. The purpose of the thesis is to elucidate how the rules in 32 §(1) AvtL apply to agreements closed by such means and to evaluate its suitability. The elucidation is done on the basis of, the rules? adequacy in relation to their objectives in collaboration with a comparative view on a selection of international legal framework under private law, such as DCFR, UNCITRAL Model Law, UNIDROIT Principles and CISG.Since Sweden lack a specific regulation for electronically closed agreements, all modern closing methods will be evaluated from the dated outlook of the Swedish Contract Act. In relation to entirely automated processes which results in the closing of an agreement, particular difficulty arise in correlation with prerequisites, which requires a human stance.

This master´s thesis is a comparative study of the importance of eight factors suggested in the literature to be related to the perceived utility of the service Book a librarian (Swe. Boka en bibliotekarie). Disciplinary differences were also analysed. 73 encounters between students and librarians in 11 Swedish academic libraries were studied using a survey. Six factors were significantly related (at the .05 level) to the utility of the service.

The aim of this Master's thesis is to study what place public libraries have in local politics, particularly from the point of view of the politicians. To answer this, I have interviewed politicians, participated as a silent observer of a public debate, and studied articles on library politics in newspapers and other press. The results show that politicians in general have a positive view of libraries and good co-operation with library professionals, and that they have a fairly up-to-date view of libraries. They are, however, less interested in library issues in general, and are often complacent with the way things are already running. The newspaper studies show that library issues are usually only discussed when a specific library is somehow in danger.

Man?s impact on the environment is something that increasingly becomes topical in today?s society. Because of this, several companies have started to take interest in the effects they?re responsible for, not least considering their image. Emissions of carbon dioxide generated from goods traffic are accountable for a large part of the total emissions of greenhouse gases in the world.

AbstractThe Northern Wheatear (Oenanthe oenanthe) is a small insectivorous passerine bird living in open landscapes. Both parents feed the brood of approximately five chicks, but little is known about how each sex allocates their feeding effort. In this study I investigate feeding nest visit differences between male and female Northern Wheatears relative to the age of the chicks, the number of chicks and the quality of the territory for 17 pairs from 2008-2010. Data were collected using automated data loggers to record nest visitation rates during chick feeding, and the sex was determined from nest video cameras. I also examine if the parents? rate of feeding visits changes over the nestling period.

In studies of serum, in the early 1930s, from patients with pneumonia, a factor was found. It could agglutinate certain pneumococcal species. This factor, which later became known as C-reactive protein (CRP), increased sharply during the early and middle stages of the disease. CRP was identified as an acute phase protein and found especially in bacterial infections. CRP is synthesized in the liver by stimulation of interleukin 6 (IL-6), which is produced by the monocytes, and consists of five non-covalently bound subunits.The aim of this study was to compare two different analytical instruments (Vitros 5.1 FS Ortho-Clinical Diagnostics and QuikRead CRP Orion Diagnostica) for CRP analysis.