Texten jämför det analoga- och digitalafotografiet. Disskutioner kring arbetssättet, uttrycket i fotografiet, uppfattningen av det, de olika tekniska asspekterna och känslan i fotografiet är områden som berörs i texten. Även kamerans och fotografiets historia i allmänhet tas upp..

This report deals with the design of a controller for SmartMedia? flash memory cards, based on a hardware description found in the SmartMedia? Interface Library - SMIL. The design was made on logic gate level, using standard cells in OrCAD Capture. After simulation of the design in PSpice A/D, it was exported as an EDIF netlist, which was used to make a chip layout in L-Edit, a layout tool for making integrated circuits. The layout was made using a method called Standard Place and Route - SPR, where the layout tool places standard cells from a library and connects them according to the EDIF netlist.

This thesis has been adjusted because some parts are classified, some sentences might have been changed. Electric bikes are a convenient mode of transport, a good choice when long distances or tough slopes can be an obstacle.The goal of the project was to create a prototype on a locking mechanism with an inductive charger for electric bikes.The idea behind the project was to develop a user-friendly locking mechanism, where the bikes would be charged inductively when they were locked. To implement the project facts about induction, battery charging and locking devices was needed to be acquired. Circuits for induction charging were created and a lock device was constructed. A microprocessor was used to control the entire system.A prototype was designed with a locking device and an inductive charger fixed in a bike rack.The entire project became very wide which resulted in that not all of the parts of the project could be completed.

AbstractThis work was assigned by a technological company that manufactures gas detectors in which the sensor signal is processed using digital filters. These filters have been developed by a consultancy firm which converted previously used analog filters to digital filters. The purpose of this work has been to analyse inadequate, and sometimes erroneous, documentation from the project in order to provide the company with know-how and tools for further improvement of their products. The work has been done using the simulation software COMSOL which was bought solely for the project. Analysis showed serious flaws as well as pure errors in the consultant?s documentation.

This master thesis describes the development of an UPS module. UPS is an acronym for Uninterruptable Power Supply. The UPS module has been developed at the company AerotechTelub AB. The UPS module delivers the necessary voltage and current in case of a power interrupt. If a power interrupt occur, the computer system has one to three minutes available to store data and shut down correctly.

This thesis has been adjusted because some parts are classified, some sentences might have been changed. Electric bikes are a convenient mode of transport, a good choice when long distances or tough slopes can be an obstacle.The goal of the project was to create a prototype on a locking mechanism with an inductive charger for electric bikes.The idea behind the project was to develop a user-friendly locking mechanism, where the bikes would be charged inductively when they were locked. To implement the project facts about induction, battery charging and locking devices was needed to be acquired. Circuits for induction charging were created and a lock device was constructed. A microprocessor was used to control the entire system.A prototype was designed with a locking device and an inductive charger fixed in a bike rack.The entire project became very wide which resulted in that not all of the parts of the project could be completed.

Keramik, foto. Text, musik. Hur kan dessa element sammanföras? Denna process, både fysisk och psykisk, har varit en bearbetning utav såväl materiella som immateriella material.I den musikaliska genre jag tillhör finns en mörk sida jag känner ett starkt släktskap till. Detta mörker finns alltid i min skugga men stundom blir svärtan däri djupare.

This is a thesis about The Eight Circuit Model, a modern mind map developed for the purpose of illumination and enlighenment by Dr. Timothy Leary in the 1970s. Later, authors such as Robert Anton Wilson and Antero Alli elaborated upon the idea to make it more wholesome and compatible with other ideas expressing the same basic principle. In short, it is an intellectual abstraction of the evolution of consciousness through a series of eight stages, which Leary called Circuits. By looking at the brain as an evolving bio-computer, with thoughts working as software, upgrading itself through neurological imprints, Learys created a Hero's Journey for the modern age.The thesis tries to analyze this idea, as it is presented in Robert Anton Wilsons Prometheus Rising, through the lens of the discourse category ?Western Esoterism.? A hard-to-define subject but described as ?the dialectic of the hidden and the revealed in the field of religion.?.

This thesis is basically a design project aimed to find a safe and reliable automatic safety device, which is designed to be suitable for highly automated industrial situations. This device fits with ABB / Jokab Safety?s fence systems. These are built up around machines to create safety distances. The automatic protection device assist the operator in situations when loading or going in and out of the danger zone.

Calesco Foil AB is a manufacturer of thin flexible circuits for heating or electric conduction.The plant is located in Kolbäck, Sweden.One of the company?s products, the conducting polymer pasta is in present situationunpredictable. Unpredictable in the way that the same type of heater shows differentresistance, depending on which time they have been produced. The desired repetitivelyprocess is almost non-existing.The aim of this master thesis is to primary identify those parameters that effects theresistance, observe and if possible to perform tests on them. The results from this analysisstand as base for recommendations to achieve a repetitive and standardized printing process.The results and the observations from the tests indicate that a repetitive process is possible toachieve.

This thesis is basically a design project aimed to find a safe and reliable automatic safety device, which is designed to be suitable for highly automated industrial situations. This device fits with ABB / Jokab Safety?s fence systems. These are built up around machines to create safety distances. The automatic protection device assist the operator in situations when loading or going in and out of the danger zone.

A case study of professional interaction designers' usage of design materials was conducted. Five interviews were performed in order to gain insight in the systems used by designers, how these work, how they collaborate within them, and what they think of recent research about them. Design studios allow collaboration for several users at once. Digital material (mockups, pictures, etc.) are commonly used, but needs to be made analog, e.g. printed, to be usable in the design studio environment.

Jag har i det här arbetet gjort en analys av skillnaden mellan analog och digital summering avljudspår. Analyserna gjordes med avseende på frekvensspektrum, transientrespons och fasdifferens.Det gjordes genom att jag skrev och spelade in två låtar att använda till analyserna, mixade dessaoch körde ut till 24 separata ljudspår per låt. De summerades sedan på tre olika mixerbord och i treolika mjukvaror, för att sedan med Adobe Audition analysera hur frekvensspektrum,transientrespons och fasdifferens ändrats. Därefter gjordes genomsnitt för de analoga och de digitalasummeringarna för att se om det fanns några skillnader dem emellan. Även om det fanns gott omskillnader mellan mixerborden så var fasdifferenser det enda som var genomgående för alla analogasummeringar mot de digitala..

Målet med examensarbetet var att ett trådlöst mätdatainsamlingssystem ska tas fram för att ersätta det trådburna insamlingssystem som idag används vid FOI i Bromma, vid mätning på vindtunnelmodeller. Projektet innefattar konstruktion, inköp, dokumentation, test och utvärdering. En del i projektet är att utvärdera ett nytt CAD system för kretskortskonstruktion.Enligt framtagen kravspecifikation konstrueras ett signalkonditionerande kort som förstärker, balanserar och filtrerar insamlad signal samt ett processorkort som digitaliserar och skickar konditionerad signal trådlöst till mottagande del.Prototypen som projektet resulterar i, uppfyller de krav och specifikationer som FOI hade på det nya systemet, dvs. analog signalkonditionering, digitalisering och tvåvägskommunikation. Systemet har med sin enkla funktion påvisat att lösningen är realiserbar och att den fungerar.

Instruktionsmanualer är ett problem för många företag i samband med att de exporterar sina produkter. Att fylla anvisningarna med ett stort antal språk blir båda dyrt och opraktiskt. En fråga som är relevant för ett av dessa företag är vilken bild som skall användas som representant för begreppet kraft. Frågeställningen i denna rapport är således: Kommer försökspersonerna att uppleva att representerande konkreta bilder visar en bättre beskrivning av begreppet kraft än analoga abstrakta bilder. Resultatet visar att en överväldigande majoritet av försökspersonerna valde den representerande konkreta bilden som en tydlig och beskrivande representant för begreppet kraft..