The determination of the optical properties of biological tissue is an important issue in laser medicine. The optical properties define the tissue´s absorption and scattering behaviour, and can be expressed by quantities such as the albedo, the optical thickness and the anisotropy coefficient. During this project, a measurement system for the determination of the optical properties was built up. The system consists of a double integrating sphere set-up to perform the necessary reflection and transmission measurements, and a computer algorithm to calculate the optical properties from the measured data. This algorithm is called Inverse Adding Doubling method, and is based on a one-dimensional transport model.

This thesis investigates how the optical properties of paperboard influences printing with targets in ISO 12647-2. The targets for optical properties in ISO 12647-2 are defined for paperboard without optical brightening agents and fluorescent brightening agents wich makes it difficult to reach the targets when printing paperboard containing these agents.Seven different types of paperboard, some with and some without the agents, have been printed and instrumentally andvisually measured to see if there is any deviation from the standard targets and if it shows visually.The result shows that paperboard containing optical brightening agents and fluorescent brightening agents can print with targets in ISO 12647-2 but in many measurments the difference between the types of paperboard were to small to assess. The differences between the types of paperboard in the instrumental measurements did not fully correspond with the waythe panel appraised them visually..

This report present a working model for simulation of what happens to colors displayed on screens when they are observed through optical filters. The results of the model can be used to visually, on one screen, simulate another screen with an applied optical filter. The model can also produce CIE color difference values for the simulated screen colors. The model is data driven and requires spectral measurements for at least the screen to be simulated and the physical filters that will be used. The model is divided into three separate modules or steps where each of the modules can be easily replaced by alternative implementations or solutions.

In an attempt to develop a more cost-efficient material for solar   energy applications, nano-particles of nickel oxide composite in a silikatmatris manufactured with solar gelmethod and studied structurally by electron microscopy. Furthermore, the thin film optical properties characterized by Variable. Angel Spectroscopic Ellipsometry. Sol gelfilms suitability as a selective absorber surface is also analyzed by optical modeling..

Free Space Optics (FSO) has received a great deal of attention lately both in the military and civilian information society due to its potentially high capacity, rapid deployment, portability and high security from deception and jamming. The main issue is that severe weather can have a detrimental impact on the performance, which may result in an inadequate availability. This report contains a feasibility study for an All-optical free-space link intended for short-range communication (200-500 m). Laboratory tests have been performed to evaluate the link design. Field tests were made to investigate availability and error performance under the influence of different weather conditions.

In an attempt to develop a more cost-efficient material for solar   energy applications, nano-particles of nickel oxide composite in a silikatmatris manufactured with solar gelmethod and studied structurally by electron microscopy. Furthermore, the thin film optical properties characterized by Variable. Angel Spectroscopic Ellipsometry. Sol gelfilms suitability as a selective absorber surface is also analyzed by optical modeling..

The purpose of this study is to compare the energy related and environmental consequences of implementing optical sorting as a means of waste collection with those of reducing food waste. In addition to studying the possibility of implementing optical sorting in downtown Stockholm, the yielded amounts of energy from waste collection and reduced wastage will be calculated. This is done by way of literature reviews and interviews. The amount of energy that can be generated through optical sorting and biogas production via anaerobic digestion in downtown Stockholm is 29-44 TJ/year, compared to 118 TJ/year saved by completely eliminating food waste. The generated biogas can replace fossil fuels, but the required food waste contributes to increased greenhouse gas emissions as well as reduced bio diversity and eutrophication during the wasted food?s lifecycle.

The energy consumption continues to increase as the use of electronics and energy consuming equipment increases. The use of fossil fuels has to be phased out for this to be sustainable in the long run while the use of renewable energy continues to increase. A renewable energy source is solar energy but the production of heat and electricity are today very expensive compared to other energy sources and an important task for the solar energy market to grow is therefore to minimize the production cost of the solar collectors while increasing its efficiency to produce heat and/or electricity. One way to convert solar energy into heat is by using solar collectors and electricity can be produced by utilizing the produced heat, or by applying solar cells.This thesis aims to recommend a reflective material for the next generation solar collectors from Absolicon and to recommend a commercially available coating for the receiver tube of the solar collector. A market study has been carried out to investigate the cost-related aspects along with the optical and durable aspects for the optical material of the solar collector.

Sverige är för tillfället operativa med Helikopter 16 - Black Hawk i Afghanistan. Uppgiften som löses i Afghanistan är främre och taktisk sjuktransport (MEDEVAC).Detta arbete handlar om hur befintliga VMS-system i helikoptrar kan kompletteras i syfte att möta ett föreliggande prickskyttehot vid lösande av främre MEDEVAC i ett insatsområde som miljömässigt liknar Afghanistan. I arbetet analyseras möjliga tekniker utifrån aspekter från ett konstruerat scenario där helikopterbesättningarnas uppgift, insatsmiljö samt hotbild beskrivs.Resultatet visar på att MEDEVAC-helikoptrar kan utrustas med sensor-gimbaler där olika sensorer kan kombineras, vilket möjliggör spaning i 360°. Detta bidrar till den militära nyttan då helikopterpersonalens lösande av uppgift effektiviseras, chansen till överlevnad ökar samtidigt som personal och patienter kan känna sig tryggare..

Gravitational lenses are unlike ordinary optical lenses, a phenomenon corrupting our optical view of the cosmos. When we look out intospace we see celestial bodies lying with astronomical distance from Earth. There is no guarantee that what we see out there in space is actually there where we are observing it, and it may be that we see multiple images of the same star! Studies have shown that thenumber of distorted images of an n-mass (n > 1) plane lens can not exceed 5(n -1) for lighter lenses or 5n for more massive lens. This mathematical thesis covers gravitational lensing and their properties that distort light rays coming towards us from distant celestial bodies. In addition of gravitational lensing, its properties and the proof of the maximum number of distorted images, a bigger part of this work even cover two very interesting mathematical tools - the so-called Schwarz function and Bezout theorem..

Denna rapport beskriver ett examensarbete där optiska fibrer av plast integrerades i varpled i en väv. Syftet med examensarbetet var att undersöka om det är möjligt att industriellt producera ljusemitterande vävar med optiska fibrer. Arbetet delades upp i olika delar, både teoretiska och praktiska. Den teoretiska delen innebar informationssökning inom olika medier, såsom vetenskapliga artiklar och intervjuer med insatta människor inom de berörda områdena. Den praktiska delen i examensarbetet bestod av flera olika moment.

The mining company LKAB extracts iron ore in three areas in the north of Sweden, Kiruna, Malmberget and Svappavaara. The iron ore is refined and in the pelletizing plants the material is rolled to finished pellet product. The different steps of pelletizing plants causes among other things emissions to the air. It occurs occasionally stops in the production and the emissions are vented via an emergency chimney without purification. The aim for this work is to look into how LKAB may improve their monitoring of air emissions and control of ambient air quality and the analysis methods which are suitable for measuring.

Nanotechnology, one of the most interesting sciences today will no doubt have an enourmous impact on tomorrow's society and industry. One of the most interesting nanomaterial that has been discovered is the semiconductor quantum dot (QD). This material shows interesting novel properties such as a size-dependent band gap, which is an effect caused by the quantum confinement effect in all three dimensions. Due to this phenomenon the absorption spectrum can be tuned to the desired value by adjusting the size of the QD.This thesis aims to investigate how the solvent ratio of H2O/Ethanol affects the optical and structural properties of copper sulfide QDs manufactured in a chemical synthesis way using modern microwave heating. The process of manufacturing QDs using chemical synthesis often involve a capping-agent to prevent the QDs from agglomerate into bigger structures.

The company LightLift Esystems AB manufactures patented motorized lift systems for the illumination of halls with high ceilings. The company wants a new design for singular heavy lights in order to be more competitive.This project consists of the development of the new design under the requirements and specifications imposed by the company. The new design must support lights up to 300kg and keep the overall dimensions as low as possible without modifying the driving unit.This document contains all the designing steps followed to reach the final solution as well as the material selection, manufacturing process and assembly of all the parts that form it.The solution obtained shows to be very competitive with other alternative products, since this new design triples their maximum load capacity while the dimensions are very similar.In this context, the optical appearance was also very important to the company and so it was another main objective of this project. From an aesthetical point of view, the final solution proves to be very compact and versatile since it can either be hidden behind a false ceiling or covered by a plastic case that gives the design a very nice look.Finally, the solution achieved fulfils all the requirements and specification previously imposed. It is reliable, compact, cheap to manufacture, easy to assembly and it has a good optical appearance. .

Mitt arbete handlar om mötet mellan rysk konstruktivism och science fiction. Detta har jag gestaltat i ett textilt rum inspirerad av science fictionkarraktären Doktorn ur Doctor Who. Doktorn är en utomjording av en långt mer utvecklad art och från en mer avancerad civilisation än människorna, som reser i tid och rum i sitt tids-och rymdskepp TARDIS. Jag har designat ett rum som är min textila tolkning av TARDIS innersta. Arbetet kretsar kring tankar om gestaltning av en flerdimensionalitet som bara kan anas, inte ses eller förstås.