This bachelor thesis has the purpose to visualize and document the air movementsprovided by different ventilation principles in an operating theatre. The visualizationwill be made as simple as possible in a physical model. The model and thedocumentation should be able to use in educational purposes.The study is based on the two most common systems for Airflow, currently used inoperating theatres. The first principle is displacement ventilation in which the air issupplied at low velocity along the floor. The second principle is vertical parallel laminarAirflow in which the air is compressed like a piston from ceiling to the floor.A review of literature resulted in the choice of size, design, and scale factor for themodel, as well as choices of ventilation principles and Airflows.

This bachelor thesis has the purpose to visualize and document the air movementsprovided by different ventilation principles in an operating theatre. The visualizationwill be made as simple as possible in a physical model. The model and thedocumentation should be able to use in educational purposes.The study is based on the two most common systems for Airflow, currently used inoperating theatres. The first principle is displacement ventilation in which the air issupplied at low velocity along the floor. The second principle is vertical parallel laminarAirflow in which the air is compressed like a piston from ceiling to the floor.A review of literature resulted in the choice of size, design, and scale factor for themodel, as well as choices of ventilation principles and Airflows.

This masters thesis concerns a modeling project performed at Volvo Technology in Gothenburg, Sweden. The main purpose of the project has been to develop a physical model of the climate in construction vehicles that later on can be used in the development of an electronic climate controller. The focus of the work has been on one type of wheel loader and one type of excavator. The temperature inside the compartment has been set equal to the notion climate. With physical theories about air flow and heat transfer in respect, relations between the components in the climate unit and the compartment has been calculated.

This thesis describes how a cost reduction project was done on the Packsize ondemand packing machine EM7. The cost reduction was achieved by making minorredesigns of the EM7.The project began by studying the EM7´s structure and function by working on itsassembly line. A short literature study on the subject Design for Manufacturing wasalso done.By working on the assembly line and by speaking with staff from production anddevelopment departments, a number of ideas for reducing manufacturing costs arose.Estimations of the potential cost reduction size for each proposal were done incollaboration with vendors and the purchasing department. Based on the size of the cost reduction, technical risk, impact on the assembly lineand the development time the various proposals were ranked. The two highestranked proposals were selected for further development towards finished solutions.One of the ideas that were selected to develop in to a finished solution meant thatsome of the pneumatic valves were replaced with others.

This report is written on the assignment by Nexans IKO Sweden AB in Grimsås which is a cable manufacturing company. Nexans IKO Sweden AB was in need of help to examine possibilities for saving energy by saving compressed air, in first place by using the compressed air more efficient. The task was to determine the present situation, making the airwipe stations more efficient by reducing the consumption of the compressed air and in turn save money. Even the aspects of the working environment were discussed as the noise levels from the pneumatic systems and engines are usually high. A schedule over the Airflow in the factory and the inventory over current airwipessituation was made.

Convective snowbands is a weather phenomenon that is associated with heavy snowfall in a limited area. They are formed over ice-free parts of e.g. the Baltic Sea when there is a cold easterly Airflow over relatively warm water. These convective snowbands can cause large amounts of snow along the Swedish east coast, often causing traffic hazards. Sometimes they can even paralyze an entire community.  In this study, convective snowbands that have formed over the Baltic Sea during the period 1980-2009 are examined, in order to find out how often they occur, what place they are most common and in what month they usually appear.

Energy supply in Sweden year 2011 amounted to 577 TWh. The final energy consumption for industrial, residential and service was 379 TWh. Sweden has energy policy goals to reduce energy use in buildings. One of these goals is to reduce the energy use by 20 % in 2020 compared to the year 1995. An important step to achieve this goal is to target energy efficiency measures in existing buildings.

This report was performed in order to evaluate a new technological measure and focuses generally on a heat pump system to a HWC-washing machine. The client is Asko Appliances AB, a company well known for its environmentally friendly products. The goal of this study was to improve the energy efficiency of a washing machine by combining a heat pump device to the heater of the wash water, in order to reduce the energy consumed for heating the water. Besides reducing the energy consumption in heating the water, the washing machine was required to meet low noise and short operating time specifications. For that purpose, nine trials in three test series have been carried out.

This thesis is a product development project that was performed at Alfa Laval Tumba AB. In the past Alfa Laval have manufactured gas separators for engines where gas flows were cleaned from oil. A new business area for this kind of technology has shown to be the manufacturing industry where oil mist has to be separated from the vented air. Therefore a new and bigger design is needed to be able to handle the greater gas flows. A product like that would be a strong competitor on the market when the maintenance would be low in comparison to today?s equipment.During the project several concept suggestions were developed using customer interviews and research as input.

This thesis describes the redesign ofequipment designed for drying bags thatis used in Fresenius Kabis´manufacturing of their nutritionmedicine in Uppsala. The need of thistask arise during the start of thedevelopment of a new packaging line werethis equipment were meant to be used. Anevaluation of the bagdryers capacity andcapability was necessary.The work started with gathering ofinformation from suppliers of the usedcomponents and from the responsibleengineers for this equipment. Aneducation to learn how the equipmentworked and how to operate it were taken.That was followed by the creation of astudy plan were the tests were plannedto test different parameters effect onthe drying result and to see if thebagdryer managed to handle the bags ofthe correct format in the pace that theequipment should be designed for.The test results detected a need ofdesigning a unit with a function thatholds the bags in place while passingthrough the dryer in order to attainhigh quality results. The results werelater used for optimization of thedesign.

In Sweden, grass is the single largest crop grown. Nearly 1 000 000 Ha grows on the fields, this is primarily used as feed for livestock. To get a good seed, you need to handle the crop carefully from planting to delivery. The part that I have been interested in, is how to dry the harvested seed with out destroying the growth in the small seed. This is very easily done if you aren?t careful during the drying period.

This thesis describes the redesign ofequipment designed for drying bags thatis used in Fresenius Kabis´manufacturing of their nutritionmedicine in Uppsala. The need of thistask arise during the start of thedevelopment of a new packaging line werethis equipment were meant to be used. Anevaluation of the bagdryers capacity andcapability was necessary.The work started with gathering ofinformation from suppliers of the usedcomponents and from the responsibleengineers for this equipment. Aneducation to learn how the equipmentworked and how to operate it were taken.That was followed by the creation of astudy plan were the tests were plannedto test different parameters effect onthe drying result and to see if thebagdryer managed to handle the bags ofthe correct format in the pace that theequipment should be designed for.The test results detected a need ofdesigning a unit with a function thatholds the bags in place while passingthrough the dryer in order to attainhigh quality results. The results werelater used for optimization of thedesign.

The viscosity of air buildings is a hot topic within the construction performers, which the industry feel they have too little knowledge about. This study is mainly aimed against air density in apartment buildings and Airflow measurement. The study consists of a theoretical reference, educational visit, interviews and a survey conducted among construction workers at Magistratshagen in Linkoping.Earlier requirement in terms of air leakage through the climate screen was removed and today there are only energy requirement for a dwelling in Boverkets Building Regulations. The difference between a passive and a typical air tight construction is that the passive house have a maximum requirement of 0.3 l /s m2 of air leakage through the building climate screen. The requirement imposed on passive houses is to minimize the supply of power and energy for heating the building.Air tight constructions have heavy demands on the performance and accuracy of everyone involved with the project. The client must specify their requirements and also be prepared to pay for any additional costs. The architect and building planners have to design the building with regard to air tightness. Finally, the construction workers are required to do a careful work in order to get all the connections in the building air tight.The study suggests that an air tight building is a closed system where no forced ventilation exists. There are no reasons not to build too tight as long as there is a functioning ventilation. In this study the authors ask themselves how an air tight building changes over time. No theoretical information has been found on these changes, but the respondents assume that air density decreases with time. The deterioration is mainly assumed to be caused by construction materials changes over time. The study shows that construction workers knowledge of air tight construction is mixed, which they themselves admit in the survey..

A passive house in Norra Djurgårdsstaden drawn by Tengbom Arkitekter is going to be built. A shaft for airing is needed for a few apartments in the house.The airing shaft is designed for a few two room apartments in the house, which are not able to achieve satisfactory airing, as their outer walls are facing a single direction. The other apartments on the same floor are corner apartments. These apartments do not have the same difficulty with airing since they have their outer walls in different directions, with different pressures at the facades. The Airflow in the airing shaft is supposed to be driven only by natural forces, by the sun. The purpose of natural driven forces is to achieve low energy consumption for the house.In this thesis, a design of the shaft for airing has been developed.Initially an open shaft for all apartments was analyzed.

With climate change, the temperature and relative humidity in Sweden are increasing. The majority of historical environments lack protection against this increase, which also increases the risk of mold infestation in these environments. One of these environments is N??s Slott, in which several rooms have recurring mold growth on objects and furniture. By examining one of the rooms in the castle that is in the risk zone or has mold growth, factors behind the mold growth can be investigated in order to create a basis for future actions against mold.