FSC (Forest Stewardship Council) is the major form of certification system in Swedish forestry today and its more than 11 million hectares are covering almost half of the total productive forest area in the country. Its regulations prescribe that at least 10 wind firm trees should be left behind after every clear cutting operation. This study have taken place on 30 recently clearcut objects in Bergslagen, Sweden, were an inventory of the standing stock have been made. The research shows that, with 90 % security, the retained trees together contain 9-13 m3sk per hectare. Pine is the dominant tree and it covers more than half the numbers of retained trees and its volume cover 65 % of the retained trees total volume. Spruce is on second place with 30 % of the retained trees, but only 21 % of the standing stock.

This thesis is a feasibility study into how Fresenius Kabi may rationalize their destruction process in regards to cost, recycling, and work environment. The two main objectives are to identify scrap flows and the possibility to improve or replace the equipment that is now carrying out the physical scrapping. The flow has been visualized by a flow chart of the material and communication. A chart of the problem established to visualize where improvements are necessary. Based on the problems proposals are presented on how to improve the flow thru the plant.During analyze of the physical scrapping equipment it was also necessary to take a deeper look at how they are carrying out there work today, how does the procedure look like, working environment and where are the weaknesses.

Denna rapport är ett examensarbete på C-nivå som görs i sammarbete med teknikkonsulten Ramböll. Det vanligaste sättet att ventilera en byggnad idag är med så kallad CAV-ventilation (Constant Air Volume). Denna metod bygger på att ett luftflöde bestäms för rummet och upprätthålls med konstant flöde. En annan metod är så kallad VAV (Variable Air Volume) som bygger på att flödet varierar efter behovet. Anledningen till varför man väljer VAV istället för CAV är att med CAV finns det ofta en stor risk att man överventilerar ett rum eller byggnad, just på grund av att flödet är konstant. Problemet med VAV är att det är en högre investeringskostnad än för CAV så metoden lämpar sig bara där energibesparingen är så stor så den täcker mellanskillnaden i pris.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

The purpose with this study is to find out how much dead wood we can expect us to find in a Russian reference river and compare with studies from Swedish streams. Dead wood are an important structure for the biodiversity in forest streams, studies have shown that population of trout can increase with up to 300 % when the amount of dead wood are increasing from 0 to 8 ? 16 LWD (Large woody debris)/100 m2. Dead wood are also an important structure for the stream character, formations of dams and pools which are important habitats and reproduction areas for salmon and brown trout. The study where taken place in tributaries to the Russian river Varzuga in the North West part of Russia outside Murmansk. Varzuga has low impact of human activity and is considered to be a reference river to rivers in northern Sweden.

Sweden is a country with few native tree species. According to Govt. 2007/08: 108, exotic tree species may be seen as an opportunity to increase the growth of tree volume in Sweden. Potential areas where explored In this work for cultivation with Pinus contorta var. latifolia Engelm., Larix sukaczewii Dylis, Abies lasiocarpa (Hook.) Nutt., Populus × wettsteinii Hämet-Ahti (tremula x tremuloides) and Picea mariana (Mill.) Britton et.al.

Increased competition in the IT industry has sparked a need for developing faster innovation processes with more predictable output. One of the biggest issues when it comes to achieving a faster flow through the innovation process lies in managing its high degree of variation. Proposing a solution to this problem, Lean Software Development (LSD), was developed to provide a framework for how IT companies should organize its software development process to achieve increased speed and quality. This study examines to which extent LSD, as a set of values, principles, methods and tools, can be used to improve flow efficiency in the innovation process. A case study of a multinational IT company was made by conducting ten semi-structured interviews with current employees.

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution.

Ett undersöknings- och utvecklingsarbete för att lösa ett problem med att dränkbara pumpar i ett vattenavrinningssystem gick sönder med perioder på två år i genomsnitt, utfördes i samarbete med Cementa AB i Skövde. Orsak till pumpars haveri söktes och fanns vara bristande rutiner och kunskap om det underhåll pumparna krävde. För att lösa detta problem utvecklades riktlinjer för nyinköp av torruppställda pumpar för att möjliggöra kontinuerligt underhåll. Då möjligheter för placering av torruppställd pump saknades utvecklades ett pumpfundament för placering av torruppställd pump. Krav för utvecklingsarbetet togs fram i samarbete med Cementas underhållsavdelning och teoretisk dimensionering av dränkbara länspumpars dåvarande volymflödeskapacitet utfördes.

Piles of deadwood are often retained in forests after management to support the biodiversity ofsaproxylic organisms which depend on deadwood to survive. Any knowledge about the crucial role ofpiles as suitable habitat of saproxylic organisms compared to single distributed deadwood objects thatare around the piles would help conservation actors to motivate more forest owners to supportsaproxylic organisms during their management. Therefore to give facts to this the saproxylic fauna ofdifferent pile positions (up and low) was studied and compared to distributed deadwood samplesaround each pile. Our study was focused on saproxylic beetles. Some other parameters such asdiameter, deadwood volume, pile volume and decay stage were assessed to define any effect.

At the beginning of the 1970´s forestry feared an imbalance in the future wood supply. Because of this anticipated "timber slump" forest companies undertook a variety of measures to counter this. One of these measures was the introduction of exotic tree species. The choice finally ended up with lodgepole pines which were considered a fast growing tree species compared to our native tree species. Theambition for the new lodgepole pine stands were to run these with rotation periods of between 40-60 years, thus smoothing out the ?timber slump? that was anticipated.

Mathematical models possible to simulate are of great importance in order to make successful projects in the aircraft manufacturing industry. An aircraft fuel system is very complex, containing pipes, tanks, orifices, valves and pumps. The principal of this thesis is using the tool Easy5, which no longer is considered reliable enough in terms of development and support. This thesis tries to evaluate the Modelica language as a possible alternative to Easy5. To make this evaluation, the components concerned in the fuel library in Easy5 are implemented to the Modelica language.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution. The work proceeded with an extensive search for abrasive flow meters along with obtaining information about flow measurement in general. When the search for abrasive flow meters resulted in nothing all the efforts were concentrated on finding a principle of measurement that could cope with the criteria.

The competition for Norway spruce pulp wood in Central Sweden increases, forcing the supply-structure of Holmen to face two important challenges. Firstly, it is of the outmost strategically importance to secure the long-term supply of Norway spruce pulp wood to the industries. Secondly, Holmen desires to increase the obtainable volume of Norway spruce pulp wood. This would enable the company to choose volumes in the lower price-segments and thereby decrease the dependency of costly marginal volumes. As this work shows, one part in managing these challenges could be to lower the quality standards concerning root rot (Heterobasidium annosum). Facts presented in the work shows that: 1. Technically, the TMP-industry of Braviken can handle a much more rotted pulp wood than that used today, although the cost of refinement increases.