A district heating plant has the advantage that it can take advantage of the waste heat from industries and use of cheap fuels to produce heat. But for the long term is competitive requires that energy is also saved in district heating plants. One way to save energy in a district heating system is to increasing cooling to the return temperature. This leads to less power needed to drive the distribution pumps,  and that more energy could be extracted from the same amount of fuel by an improved flue gas condensation.In Karlskoga the return temperature into the district heating plant is high. They would therefore reduce the return temperature in order to extract more energy from the flue gases.

The present climate discussion has made energy efficiency an interesting topic. Saving energy does not only help the climate but also saves money for the energy consumer. The purpose of this thesis was to examine the potential of heat recovering from milk cooling. Two milk farms, one with voluntary milking system, VMS, and the other with conventional milking system was used to measure interesting temperatures and electricity consumptions. The numbers were used both to do theoretical calculations and to construct a SIMULINK model. To calculate the potential for heat at milk farms theoretical calculations were made in MATLAB using a reference farm with different combinations of heat recovery and pre cooling. The farm was assumed to keep a dwelling house with the annual heat consumption 18165 kWh.

The vision of this thesis was to create a concept that can be used as a base for amachine construction. The purpose of this project was to use different methods todevelop a concept that on the best way meets the sat up requirements. This projecthas been divided into three stages/parts; principle, primary and the final solutionstage.This thesis has been conducted in collaboration with Västkustägg AB. It is aconstruction project designed to construct a machine that will automatically putlabels on the egg packages. Västkust AB wanted to automate this process.

This report describes a synchronous machine model with magnetic saturation in d-axis, neutralconnection and electrical exciter interface for the transient simulator PSCAD/EMTDC. It hasbeen designed and verified in comparison to the regular machine model in EMTDC.The performance of the model is very good when incorporating a linear as well as a saturatedmagnetising inductance. The dynamic deviation is only thousandths to ten thousandths perunit. By using a cubic interpolation of the saturation curve, the model gives a good representationof the saturation effect. The open source code implementation of the synchronousmachine model gives the possibility to easily adapt the model to specific requirements.The derived model makes it possible to simulate a synchronous machine with its excitationsystems, e.g.

Svenska Aerogel AB has developed the material Quartzene® which is of the typeprecipitated silica and contains calcium - magnesium silicate ((Ca, Mg) SiO3). Thematerial is used for molecular filtration of contaminated air. Qartzene?, which is inpellet form, is porous and has a high internal surface which is a requirement for themolecular filtration. With the use of various impregnations, filtration can affect thedesired outcome.

Metso Paper offers a front-running range of solutions and services for the pulp and paper industry. At the baling unit, design solutions are developed for manufacturing and handling of pulp bales. The machines are continuously developed to satisfy customer needs. One big step in the development of the baling line was to remove hydraulics from the machines and replace it with electrical motors and pneumatics. This was not done on the folding machine which is still driven by mainly hydraulics.

The purpose of the project has been to work out recommendations that reduce the energy-related costs and environmental impact of HPW Fresh & Dry Ltd., a fruit drying factory in Ghana. The factory produces electricity with diesel and biogas but also purchases electricity from the national electricity company. Heat for the drying process is produced from biogas, kerosene and solar panels. In the project the energy system was analyzed by measuring production and consumption of heat and electricity. The project results show that the factory can become self-sufficient on heat if the available energy is used more efficient. The production units for both electricity and heat have low efficiencies.

This paper describes the process of building a machine translation lexicon for use in the train and transport domain with the machine translation system MATS. The lexicon will consist of a Swedish part, an English part and links between them and is derived from a Tradostranslation memory which is split into a training(90%) part and a testing(10%) part. The task is carried out mainly by using existing word linking software and recycling previous machine translation lexicons from other domains. In order to do this, a method is developed where focus lies on automation by means of both existing and self developed software, in combination with manual interaction. The domain specific lexicon is then extended with a domain neutral core lexicon and a less domain neutral general lexicon.

The project was made in cooperation with Coffee Queen AB, Arvika. The task was to develop and design a new cooler for the milk to Jura Impressa X9, an espresso machine. The good assistance with staff at Coffee Queen and engineers in China and at KPA in Karlstad led to a solution to the problem. It was a long road to get there, many different concepts was developed. When the day came to decide which concept to work with, the choice stood between two different technical solutions.

This report describes a synchronous machine model with magnetic saturation in d-axis, neutralconnection and electrical exciter interface for the transient simulator PSCAD/EMTDC. It hasbeen designed and verified in comparison to the regular machine model in EMTDC.The performance of the model is very good when incorporating a linear as well as a saturatedmagnetising inductance. The dynamic deviation is only thousandths to ten thousandths perunit. By using a cubic interpolation of the saturation curve, the model gives a good representationof the saturation effect. The open source code implementation of the synchronousmachine model gives the possibility to easily adapt the model to specific requirements.The derived model makes it possible to simulate a synchronous machine with its excitationsystems, e.g.

Lars Höglund AB is one of Scandinavia?s most qualified manufacturers of sheet metal products and provides custom designed products of very detailed precision. One of the main methods of manufacturing is laser cutting. When Lars Höglund AB signed up a new customer, with high demands in tolerances for the products, Lars Höglund AB thought it would be necessary to know the capability of the laser cutting machine. Also the process of how to retrieve this capability was interesting. The capability will be researched for the following elements: Cutting right angles in squares with a corner radius of 1 mmCutting corners which are not right angleCutting of circles with constant radius Measurements were made on 150 pieces of sheet metal details, which had been cut out by the machine.  The data from the measurements where later used to study the capability.

In Uppsala CHP Plant, there are six pressure reducing valves to reduce the pressure from 15 to 3 bars, before six absorption heat pumps. During the process the energy is conserved but losses occur in form of exergy. The aim of this thesis is to reduce the losses of exergy. This can be done by letting turbines replace the pressure reducing valves.In this thesis an investigation has been done of the conditions today, the conditions after the change from pressure reducing valves to turbines and a comparison of three different types of turbine solutions. The three examined solutions are one turbine, several helical screw expanders and several small turbines in parallel with asynchronous generators.The six absorption heat pumps have been divided into two groups; one group of four and one group of two absorption heat pumps.

We are getting smarter. Our knowledge of the world around us is increasing rapidly and our population spend a big portion of their time in school studying it. But art and craft are moving out to give room for more theoretical subjects. Today many of us can not even fix a torn shirt without help. We buy new ones, they are cheap enough.

Costs of maintenance on agriculture machines is something that many farmers has a low knowledge of, it can depend on low interest or that the farmer don?t have enough time. To make it easier for the farmers they can use many computer programs which are available on the market. In this program they can calculate their costs of maintaince on their agriculture machines, for example STANK and JTI machine calculation program. Most of this program is using Svensson (1987) costs model whish was made in Sweden in the middle of 80 decade in a large study.

This report shows methods and workflow when exploring the potential to change Outotecs HCD Silver Electrolysis machine to a module type. It?s done as an attempt to lower the workshop and installation costs and to give customer a more accurate prize directly. To do this a concept was produced which was set to a stress test. Additional objectives were to investigate freight and installation procedures, pneumatic connections and to calculate the difference in cost.Once the concept, a reinforced type of the original frame, was chosen stress tests in computer simulations were made and appropriate alterations were made.