This report is a study in voltagelevel in connection with regeneration of brake energy from the tramtype M31 in Gothenburg.In the act of braking, the tram M31 uses electrical braking where the electrical motors generates energy and if possible send it back to the overheadline, where other trams in the nearby can use this regenerated energy for its own driving force. In cases where no other energyconsumers are located in the same section, there is a resistance witch task is to convert this energy into heat. The regulation of this resistance appears to cause an increase in the voltagelevel into far too high levels.Investigations of the trams regulationequipment and its construction have been done. Further have measurements on the overheadline been performed in order to map the voltagevariations during a longer period of time.The result have been showing that the voltagelevel during regeneration often is as high as 880V-920V, more extreme values have not been observed in a large scale. The values are especially high compared to the nominal voltagelevel.

This report is a study in voltagelevel in connection with regeneration of brake energy from the tramtype M31 in Gothenburg.In the act of braking, the tram M31 uses electrical braking where the electrical motors generates energy and if possible send it back to the overheadline, where other trams in the nearby can use this regenerated energy for its own driving force. In cases where no other energyconsumers are located in the same section, there is a resistance witch task is to convert this energy into heat. The regulation of this resistance appears to cause an increase in the voltagelevel into far too high levels.Investigations of the trams regulationequipment and its construction have been done. Further have measurements on the overheadline been performed in order to map the voltagevariations during a longer period of time.The result have been showing that the voltagelevel during regeneration often is as high as 880V-920V, more extreme values have not been observed in a large scale. The values are especially high compared to the nominal voltagelevel.

Bakgrunden till rapporten var att det företag som medverkat i studien ville utveckla ett grundmönster för damkappor. Syftet med arbetet blev därför att utarbeta ett grundmönster med två ärmtyper som graderas mellan storlek 32-50, samt konstruera en kappmodell från samma grund. Utöver detta skulle även detaljkonstruktioner och specifikationer utformas. Frågeställningarna som styrde arbetet kretsade därför kring hur man på bästa sätt tar fram detta.All konstruktion utfördes i Lectra´s Modaris. För att ta fram grundmönstret jämfördes två arbetssätt för att sedan välja en av de grunder som konstruerats.

According to Edward Said the Orient is a European construction that has arisen out of a need to describe the Western civilisation as culturally superior. This occurrence Said gives the label "Orientalism". Art historian Linda Nochlin takes Said?s theories further in The Imaginary Orient where she conveys the thesis that the pictorial Orientalism is an expression of an imperialistic ideology. John M.

The purpose of this study is to examine constructions of plaintiff [woman] and the defendant [man] in Swedish rape convictions from 2013. The cases in this study cover acquaintance rape. We also intend to analyze the constructions of the sexes in relations to each other. The study is completed by a qualitative text analysis, with inspiration of a hermeneutic interpretation. The result is presented by four categories: the worthy of protection of the woman, the penalty of the man, the complicity of the woman and credibility.

This report is a study in voltagelevel in connection with regeneration of brake energy from the tramtype M31 in Gothenburg.In the act of braking, the tram M31 uses electrical braking where the electrical motors generates energy and if possible send it back to the overheadline, where other trams in the nearby can use this regenerated energy for its own driving force. In cases where no other energyconsumers are located in the same section, there is a resistance witch task is to convert this energy into heat. The regulation of this resistance appears to cause an increase in the voltagelevel into far too high levels.Investigations of the trams regulationequipment and its construction have been done. Further have measurements on the overheadline been performed in order to map the voltagevariations during a longer period of time.The result have been showing that the voltagelevel during regeneration often is as high as 880V-920V, more extreme values have not been observed in a large scale. The values are especially high compared to the nominal voltagelevel.

This report is a study in voltagelevel in connection with regeneration of brake energy from the tramtype M31 in Gothenburg.In the act of braking, the tram M31 uses electrical braking where the electrical motors generates energy and if possible send it back to the overheadline, where other trams in the nearby can use this regenerated energy for its own driving force. In cases where no other energyconsumers are located in the same section, there is a resistance witch task is to convert this energy into heat. The regulation of this resistance appears to cause an increase in the voltagelevel into far too high levels.Investigations of the trams regulationequipment and its construction have been done. Further have measurements on the overheadline been performed in order to map the voltagevariations during a longer period of time.The result have been showing that the voltagelevel during regeneration often is as high as 880V-920V, more extreme values have not been observed in a large scale. The values are especially high compared to the nominal voltagelevel.

The author of this report has created a Web-based invoice system and CRM at therequest of the company Webhouse.se. The purpose of the System is to makeeveryday tasks in the company easier. The system also needed to prevent mistakesand errors by managing orders and invoices.The system has been created with the company?s requests in focus. During thedevelopment of the system information security and interaction design have beenimportant aspects that have been taken into consideration.The system has been created using techniques such as PHP and MYSQL.

To be allowed to sell Z-suspended vehicles with dipped beam Xenon or LED lighting, Scania have to develop automatic headlight level control. This master?s thesis aims to be the foundation to that development.The thesis consists of several parts; a market analysis of how competitors to Scania and the general vehicle industry solve this problem; several available principles for detecting the amount of control needed; the construction of a test station for sensors, a control unit and components connected controlled by the control unit; a further theoretical and practical development of one principle ? one rotational sensor connected between the chassis and the back drive axis; a state flow model programmed in Simulink that produces the control signal for the headlight leveling from the sensor input.Lastly the thesis gives some recommendations to the further development and implementation of automatic headlight level control on Scania vehicles..

Dione kullager AB is a company in Uppsala, which sell industrialmachinecomponents, transmissionsolutions and provides repair serviceof hydraulic components.When a hydraulic cylinder is about tobe repaired it needs to bedisassembled. Because hydrauliccylinders usually work in dirtyenvironments and are heavilyworn some types of cylinders arealmost impossible to disassemble.Today the disassemble is made by hand,which means extra work for themechanics. In order to facilitate thedismantling of this type of cylindersa machine is to be developed for thispurpose and this is where this thesisbegins.The thesis has been organized in threephases: Literature study in whichfacts and theories are acquired.Concept generation in which differentconcepts, calculations, and solutionswere identified and selected. Thedesign phase where all the differentconcepts of components were assembledand simulated in SolidWorks. Similarstructures have also been studied inorder to identify necessary functions.The thesis resulted in a structurewhich is believed to meet therequirements.

Syftet med detta examensarbete är att producera ett dataprogram som dimensionerar pålfundament samt beräknar felslagning av pålar. Ett pålfundaments funktion är att via pålar överföra laster till berg eller fasta jordlager. Felslagning inträffar då pålar inte hamnat på rätt koordinater eller glidit snett ned i marken och ej kan användas. Med hjälp av felslagningsprogrammet erhålles nya påkoordinater för nästkommande påle, vilken måste placeras ut så att tyngdpunkten för hela pålsystemet skall hamna rätt. Programmeringsspråket vi använt oss av är Visual Basic, där vi har omvandlat teoretiska beräkningar till databeräkningar.

The object of this examination project is to produce a method of work sampling at Rapid Granulator AB. The aim is to perform the method at the company and evaluate if it is executable. The study is delimited to the basic construction of the 45-series in the assembly hall.Preparations to produce the method of the work sampling resulted in definitions of activities, a form and a product tree. Several days were spent studying the assembling to learn and understand the entirety.The work sampling result showed a large amount of no value adding time that was used in the assembling. Some of the activities could be reduced and we observed some problems during the assembly process.

Detta examensarbete är genomfört åt Sandvik Mining and Construction inom ramen för det statliga samarbetsprojektet MinBaS II. Sandvik Mining and Construction är ett av Sandvik koncernens affärsområden och har en världsledande position på marknaden för maskiner och tekniska lösningar för bergbrytning m.mMinBas II är ett samarbetsprojekt mellan ett stort antal företag och universitet där staten står som huvudman och löper till 2010.Uppgiften med examensarbetet var att se om det fanns någon metod för att kartlägga de interna transporterna och beräkna deras energiåtgång i en bergtäckt. I brist på en befintlig skulle det tas fram en ny metod och sedan testa denna genom att genomföra fältstudier i en bergtäkt tillhörande Skånska Makadam AB för att sedan göra beräkningar på energiåtgången där.Volvo CE har under arbetet ställt upp med information och även givit oss SiteSimulation, ett simuleringsprogram för simulering av användning av deras maskiner.En del av arbetet var också att utreda hur energiåtgången ändras om förkrossen placeras på en högre respektive lägre nivå än det ställe där bergbrytningen genomförs.För att införskaffa underlag till beräkningarna har fältstudier genomförts i Skånska Makadam AB:s bergtäkt. Där gjordes bl.a. uppmätningar av den fysiska miljön som t.ex.

I takt med att besökare och patienter ökar måste kontinuerligt Östra sjukhuset verksamhet utvecklas. Detta medför omläggningar i trafiken och förflyttningar av verksamheter. Idag finns flertalet brister kring Östra sjukhusets fysiska planering som behöver ses över, dessa är bland annat trafikflöden, säkerhetsaspekter och parkeringsmöjligheter.Rapporten redogör för förändringar i den fysiska planeringen som förbättrar dess utformning. Genom studier av relevant litteratur och diskussioner med expertis har förslag av problemområden tagits fram. Dessa har sedan bedömts efter listor av deras respektive för- och nackdelar som kunnat urskiljas.Arbetet visar framtagandet av ett väl fungerande förslag som kan verka som en bas för idéer till nutida och framtida förändringar kring den fysiska planeringen.

Injuries and sick-leave is a common feature for reinforcement workers today. This is mainlydue to the fact that reinforcement work is done in an exposed environment with many stressfactors and highly repetitive work. These operations are often carried out in unsuitableworking positions, these positions creates a major burden on the bones and joints and causesmicro- damages on muscles. With repetitive work these injuries are not given time to healproperly and will gradually become worse.The body will not be able to handle the stress of working in a work environment such as thisand musculoskeletal disorders can be a result of this. The injury will make itself known aspain in the musculoskeletal system and causes reduced movability; the injured worker willtherefore not be able to perform the same work tasks as before.