This thesis work is made by Torbjörn Johansson on Karlstad University for Uddeholms AB. The assignment in this thesis work was to investigate tough cutting in three different tool steels: Vanadis 4 Extra, Vancron 40 and Sverker 21. The research was to compare the wear of the tool after cutting in each one of the tool steel alloys. The research was also made to see if the tool cutting in Vancron 40 has a better wear than the tool cutting in Vanadis 4 Extra and also compare the results with Sverker 21. All three of these alloys are a part of Uddeholms AB:s range of products, and is used in applications like forming tools and knife tools. Vancron 40 is a powder steel with a very good combination of mechanical properties like ductility, adhesive strength and hardness.

Husqvarna is a world leading producer of chainsaws with a well-established brand name. Husqvarna now has an interest in investigating the possibiltiy to expand their production of chains and guide bars to include cutting equipment for timber-harvesters.This project is a technical study which aims to answer questions about cutting equipment for timber-harvesters that have been decided in cooperation with Husqvarna. The questions have mainly been focused on forces, cutting speeds, service and maintenance -as well as general questions regarding the size of the Swedish market.Two methods have been applied to answer the questions. Interviews with retailers of harvesters, producers of harvester heads and harvester drivers.The main findings in this project show that there is a relatively small selection of harvester chains on the Swedish market. In contrast to the selection of harvester chains the selection of guide bars is quite large.

Our Bachelor´s Thesis has been performed in co-operation with Bors Automation & Tool AB.Our task was to develop a servomotor powered tube cutting-machine with initial point fromtoday's hydraulic driven tube cutting machine Bors HYD 23. The purpose with the newconstruction was to achieve a more power-efficient tube cutting machine which could lowerthe power consumption, and also meet the market continued growing demand forenvironmental-conscious production.Bors Automation & Tool gave us relatively free hands in order to enable new thinking ideaswithout following their traditional constructional solutions.Our solution resulted in a construction based on a power source existing of a servomotordrivenrollerscrew, witch provides a more rational use of energy compared with the currentmethod.Bors Automation & Tool AB has decided to fabricate a prototype of Bors E 23 during theautumn of 2007, which they are planning to revile at the Tube 2008 exhibition in Düsseldorf,Germany.NOTE:Due to an agreement signed by the authors in the beginning of this project, no appendix is published at this time.If you want to wiew these documents, please contact the authors..

The aim for this study where to investigate the frequency of cutting cracks in saw timber harvested in the storm-damaged forests in regions where the storms Hilde and Ivar hit. The idea for this work came from one of the region?s biggest actors, SCA Skog and Jämtlands district. The purpose where to find out how big proportion of the saw timber that contains cutting cracks, their financial cost in lost wood value and also give advice and suggestions on how to work against the frequency of cutting cracks. For the field-study some guidelines where used to make sure that the samples were taken under the same conditions, they were: ? The field-study must be performed under harvesting of storm-felled forest, which are horizontal/inclined trunks. ? The averaged sized tree will make it possible to harvest saw timber. ? The trunks can?t be root cut. A methodology called in Swedish ?Trissmetoden? was used because it is the most frequent used methodology in earlier performed studies and the only one that can be used I field. Under the field-study data were collected from 570 saw timber logs, 30 logs from each one of the tested harvesters.

The degree project at hand investigates how large areas of older forest (80 plus years) suitable for clear cutting there is on the Swedish island of Gotland. Large areas of older forest on Gotland are situated on land with shallow soil depths which are economically uninteresting and often unsuitable for clear cutting forestry. Other forests hold big nature conservation values and should not, or cannot, be used for forestry purposes. The survey is made as a GIS analysis based on the old but carefully made ?Brief forest inventory? (ÖSI) made in the 1980s and early 1990s. A sample from the inventory is combined with studies of orthophotos, satellite photos and other GIS layers that display estimated soil depth and nature conservation values. Partly contrary to common belief, the survey shows that there are still large areas of older forest suitable for clear cutting forestry on the island.

Steam was used as a site preparation method to eliminate unwanted bilberry (Vaccinium myrtillus L.) in the boreal forest. The efficiency of steam to suppress bilberry was compared with prescribed burning and cutting the bilberry. Different combinations of steaming and/or cutting the bilberry were set up to investigate in which way steaming and cutting influenced the sprouting and regrowth of bilberry. The regrowth of the bilberry vegetation was monitored for 40 month. Steam was most efficient in suppressing bilberry.

As the Swedish governments long term goals include a reduction of fossil fuel dependency, increasing pressure is placed upon energy companies to create and develop new solutions for renewable energy. The following case study was done in collaboration with the company Sydved Energileveranser AB and one of their contractors, Enarssons Skogsentreprenad AB. The objective of the study is to examine the bioenergy situation in region of Skåne and evaluate the potential solutions in the region for a forest-fuel assortment, based on a bioenergy-cutting-system. As a part of this study I have compared ordinary manual cuttings done with a chain saw and cuttings made using the new ?bio- energy cutting system?. The cuttings made under both systems were tested in areas near agricultural fields or pasture land in order to maintain an open landscape.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

This study is made on assignment by the local board of forestry in Skåne, Blekinge and Halland. The change of the forest law 1994 brought a new type of management plan. A more active planning was introduced in order to equate the environment goal with the production goal. The purpose with this study is to give a better picture of how planning for nature conservation in production forest is made and to develop support for selection of silviculture methods for stands with combined goals. With combined goals means production forestry with a reinforced consideration to both nature and culture, called PF-classified stands. This was done by: ? Describing silviculture models from the literature that are possible to use for stands with combined goals. ? Describing silviculture models that is used in practice in stands with combined goals. ? Describing how the classification of stands with combined goals is used. Which means, were in the terrain, with which frequency and in which type of forest PF-classification is used. ? Comparing differences and similarities of theoretical and practical used models. The study was done partly as a literature study and partly as an interview study of forest planners.

In the last decades, high speed cutting has become an attractive technology in the wood industry. The possibility of reducing global costs in addiction with an increase in productivity, were the main reasons for the enlargement of the use of this technology. As usual, these advantages are accompanied by disadvantages that should be carefully analyzed. If on the one hand cutting forces are reduced with increasing cutting speeds, on the other hand, the centrifugal forces affecting the tool are higher. Exposed to such high loads, there is a considerable risk of tool failure that embeds hazards for both machine and workers.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

This report is about planning a demolition. The purpose of this report is that it should become a base for a demolition of house J at the Academic hospital in Uppsala, and also to make general help for planning a demolition. This report also contains a part about how a change in the work environment affects general people. The work started with studies of literature and design of the general part of the report and then continued with a practical study of house J. From the experience of the first two parts of the report a general help for planning a demolition was shaped.

Different methods for shelterwood cutting have been used in differ-ent parts of Europe since the middle ages. The use of shelter wood cutting in Norway spruce (Picea abies (L.) Karst.) forests in Sweden met a revival in the early 1990s as an alternative for the dominating clear-cutting system when silvicultural costs increased dramatically for the latter. Shelterwood cutting systems involve some possible problems but also a lot of positive effects. Among the problems are increased risk of wind throw and damage of the remaining shelter trees caused by the cutting operation. Positive effects are for example a valuable growth in the remaining trees and increased biological di-versity. This study is based on a total of 79 trees from 4 different treatments in a spruce shelterwood, cut in 1994, in the middle of Sweden (62,4º N).

In Sweden today so-called "prescribed nature conservation burning" is performed due to the change in silvicultural law, certification and an increased knowledge regarding the field of fire in the forest landscape. The aim is to re-create structures and qualities made by the fire regimes of the past, though on a much smaller geographical scale. The structures and qualities to be re-created are for example broad leaf stands, trees with large diameter, heterogeneous stands regarding variables such as age and diameter. If we increase our knowledge of the constitution of forests characterized by fire, then we will be able to set goals for what achievements to reach both on landscape scale and stand scale. The aim of this paper is to try to describe how a stand from the past was composed regarding mainly the spatial arrangement and compare it with the stand of today in the same place. This to be done by using relict material, that is stumps and dead standing trees.

In this study, the pre-tension force in an insert screw connection are examined in order to establish a greater understanding of the system and to facilitate the process of making new metal cutting tools. Certain especially significant design variables such as the offset, the length of the contact thread and the shank length above the threaded hole, are selected to be closely examined. A comparison of the influence on the pre-tension force between threaded holes made with a worn, versus new, threading tool is also involved in the experiment. The study is limited to handling the screw sizes M2,5 and M3,5. The results show that a regression model, with good approximation, can be fitted to the measured values.